I am working on BLE. I have created a service using read property(services_set_barometer_service_barometer_data(void *src, int size))
After connection is set-up i am calling...
Hello, I'm using the nRF51822 and tried the HID Keyboard Application (S110, ble_app_hids_keyboard) example. (Nordic\nrf51822\Board\nrf6310\ble\ble_app_hids_keyboard )
The...
Hi all,
I have a situation in which softdevice (s310 v2) seems not to forward events to my nrf app (bootloader running dfu) in spite of the fact that my iOS app sees the...
I am sending setup commands to a NRF8001 D device and I receive a command response with status of 0x89. This appears to respond to ACI_STATUS_ERROR_UNSUPPORTED_FORMAT. I cannot...
Hi I'm working on a school project and I need to send data from an accelerometer to a phone I'm currently able to update "dummy" data from my nrf51822 to my phone after following...
Working on an ANT project.
Switched a project from S210 to S310 to add BLE feature.
For the ANT part, there is no source code modification at all.
Sweet.
This is not...
Has anyone experience of successful TICK_DV calibration for nRF9E5? What order of accuracy should be achievable?
In my application I maintain a software RTC clocked by...
I am new to chip testing and need some advice on how to start. I am trying to test a nRF51822 on a custom PCB. The main elements of the PCB are the nRF51, a GPS module, and...
Hello,
I try to perform an pstorage store action after I'm done advertising just beform the devices goes in system OFF mode. Pstorage works fine before I start advertising...
I've gotten two PCA10001 boards working with the LED_mesh sample.
I cannot get the third board to run BLE_Gateway (it does not react to button presses, nor is it discoverable...
Hello,
I established a connection between my central and peripheral module. Now i want to write characteristic value on peripheral. I tried with sd_ble_gattc_write function...
Dear all,
I'm not able yet to start advertising with whitelist whith this code:
void AdvInit(void)
{
ble_advdata_t advdata;
uint8_t flags = BLE_GAP_ADV_FLAG_BR_EDR_NOT_SUPPORTED;...
I have a nRF51 DK board and its flashed with the SD 110
I want to have a timer which will interrupt every 50us.
This is how I set up the timer:
#define APP_TIMER_PRESCALER...
I am using the NRF24l01 for my products and looking to buy in bulk(100-1000). Now I know where to buy the just the IC but antenna design is a hard point to break right now...
Hi, my friend,
I've been with nrf905. I use a 16-bit CRC check.
But I encountered problems in use:
1.Nrf905 16-bit CRC check format is CRC-16(IBM):X16+X15+X2+1 or other...
I have two custom PCBs, each of which has a microcontroller and an nrf24L01+. Everything related to the transceiver in the designs are complete duplicates (with the exception...
Hi
I'm using nrf51422 to send periodically a frame through ble_nus service to the Nordic nRF UART app. One of the frame data is the message count number, that is reset...
Hi,
I would like to install Master Control Panel on my PC.
Where can i find the installer for a windows desktop machine?
Also is there a user guide available for...
Hello,
I am currently working on a project that is using the nRF51422 chipset (Rev 2 silicon) and the S310 SoftDevice Version 1.0.0 and I am having some problems with the...
Hi all,
I have an PCA10001 board and a custom PCB which also uses the QFAA version (256KB flash, 16KB RAM). I'm trying to enable OTA feature for our custom board. I use the...
