Hi, when I am trying to set up channel sounding, I am looking for the best parameters for CS configuration. The main problem I have is that even with slow movement (1 km/h...
Dear sir,
I'm using the sample application "channel_sounding_ras_initiator" to performing the evaluation. Here are my test environment: - Developement kit: nRF45L151 - Tool...
Hello,
I previously used DECT NR+ modem firmware mfw-nr+_nrf91x1_1.0.2 on nRF9151 DK Development kit and moved on using the new modem firmware mfw-nr+_nrf91x1_1.1.0.
But...
Hello,
I’m having an issue with my setup: I have a nRF9160 running the bt/peripheral sample through a nRF52840 (running the hci_lpuart sample). It seems to work fine with...
Hello,
I am using nrf52840 MCU.
I am developing a product which have 2 I2C and 2 SPI interfaces. All the interfaces are on different pins.
I developed this thing with...
Hello all,
I am using the nrf52840 MCU and NCS v2.6.2 for my application development. Here I am using SPIM3. I am using a peripheral which have an internal FIFO. From...
The partition config for ZBOSS is set in different locations in NCS. For us this worked out magically in the past because the values that were written have been the same in...
Dear all
We did nordic beacon board in that we not able to flash the device
We are checked core voltage 1.2V and 1.7V are coming .But i want to confirm external CLOCK will...
Hi,
I want to change the interval time of 51822 dongle with the instruction here devzone.nordicsemi.com/.../
The default value is 100ms as following
#define NON_CONNECTABLE_ADV_INTERVAL...
Hey guys,
I’m working on an nRF51822 design where I’d like to check the value of a GPIO at Power-ON, then either shutdown, OR start the BLE stack and do BLE stuff. I really...
when compiling " ble_app_proximity " exampled by Nordic, it indicates errors:
" D:\Program Files\MDK5\ARM\PACK\NordicSemiconductor\nRF_Drivers\3.0.0\gpiote\nrf_drv_gpiote...
Hi:
in ble_app_proximity(SDK5.2) ,i use lightblue to write data to ble,and i set a breakpoint in "ble_evt_dispatch".but i found breakpoint can't work when i send data to...
My product have to pass SRRC certification. The certification lab need 3 prototype. Their bt RF frequency must work at 2402MHz, 2441MHz and 2480MHz separately.
How can I...
Hi ,
I am unable to write to discover all services and write to a characteristic too.
On discovering services:
Discovering primary services
Received service discovery...
One of our computing-intensive algorithm takes actually ca 1.9s to finish. And it will be run periodically. Is there a way to minimize the power consumption of CPU processing...
class BatteryService {
public:
/**
* @param[ref] _ble
* BLE object for the underlying controller.
* @param[in] level
* 8bit batterly level. Usually used to represent...
I am looking through the following mBed development platforms. I am looking to integrate some mbed code into a production design. I am looking at which platform to export...
Hello Folks,
I want to send an array of two bytes and read six bytes back . Even though I am using bellow function but the Oscilloscope shows only 4 bytes of clock cycles...
Hi,
I'm using the nrf52 preview development kit. I have two boards. I flashed one with a ble_central example and the other with a ble_peripheral example using the nrf52 sdk...
Hi,
I'm using the nrf52 preview development kit. I have two boards. I flashed one with a ble_central example and the other with a ble_peripheral example using the nrf52 sdk...
Hi guys,
My device is in peripheral role and it normally connects with phones/tablets/computers.
I tried to search for device information service but this service is...
There was a thread about this issue:
devzone.nordicsemi.com/.../
I am having the same problem again.
I am using S110, RTOS, do 10 conversions on the same channel every...
