Hello:
The latest nRF54L15 Errata for Rev 2 shows that the previously reported "GPIOs can exhibit radiated emissions" is no longer present in the Rev 2 SoC.
Can you please...
The documentation for the nRF52840's SAADC mention optional resistor ladders. What are they for? I see that the documentation specifies that the ladder's resistance is 160kΩ...
Hi, this is a very broad issue that i am having, because i dont know the source of it. I am simply unable to use the bme68x IAQ library. i have downloaded the external bsec...
Greetings!
I am using Wireshark along with an nRF52840 dongle to monitor BLE traffic between a mobile app and connected peripheral and periodically I see some "L2CAP Fragment...
Hello, I am using the nRF54L15 board, and trying to connect to the Adafruit SHARP 400x240 monochrome LCD display .
I got the display driver alone to function just fine after...
Hi,
I am trying to perform a DFU using SMP over BLE. My setup has NSIB and MCUBoot enabled and thus I am able to perform DFU for MCUboot and Application using nrf device...
Hi all,
I'm trying to use uart2 on my custom nrf9151 board, but I'm stuck. As I understand, I use i2c1 so I can't use uart1 and i2c1in parallel, so here is why I wnt to...
I'm using SDK 7.1, PCA10028 eval board, SD310 2.0.1
My application has no display, and a single button for input. I want to prevent bonding until the button is pressed...
I use Eclipse, gcc and OS X to compile.
I had FW working just fine with SD 6 and SDK 5.2. I recently tried to upgrade and ran into many problems, but the latest is the...
Hi
I've written an application that uses the gazell proprietary stack for nrf51822 and I want to use OTA-DFU using BLE.
Is it possible to upload the new firmware using...
I’m running into a problem with the SoftDevice safe twi that’s been posted in the forums a few times. I got the file here:
devzone.nordicsemi.com/.../
One of my peripherals...
Hello,
I have been messing around with a PCA10001 Dev board trying to do some power consumption tests (Beacon demo code). When I enable RTC1 only and use __WFE in the main...
Hello everyone,
I haven't read anything in the official documentation about it, but I was wondering if the S110 has an embedded checksum that I can use to verify its integrity...
Hi,
I'm currently working on nrf51822 beacon connected with stm32f4 board. able to communicate fine on UART as well as with bluetooth device. is there any way to find out...
We have been using the nRFgo nRF51822 development kit for prototyping. We now want to design our production board. However, your site says that this dev. kit is not recommended...
It seems these functions are identical in what they do, except that one is in S120 and the other is in S110.
Why not standardise the booting mechanism to facilitate code...
Hi !
I'm developing a bluetooth low energy service using the nordic evaluation kit and following the ble_lbs example. It works, but when I load the code on an other electronic...
Hello,
does the iOS Loader app not work with the nRF51422 chipset? I thought that this chip was more capable than the nRF51822. I do not seem to get access to the download...
I'm concerned about stack overflow as I consider using a linear fit function which declares 5 local variables as floats and accepts 5 pointers.
5floats * 4B/float + 5pointers...
Hello! Can anyone tell me information about bluetooth protocol and SDK functions?
What functions need to start BLE device like a peripheral/central, and what each...
My JLink Lite seems to have died (nRFgo Studio can see it, but can't connect to a target).
What is the latest replacement for a JLink Lite?
Preferably something that can...