Hello!
I'm currently working with the nRF7002 Wi-Fi chip on a custom board. The MCU used is STM32H573ZIT6, and the software is Zephyr 4.0, specifically using the Wi-Fi shell...
Hi, when I am trying to set up channel sounding, I am looking for the best parameters for CS configuration. The main problem I have is that even with slow movement (1 km/h...
Dear sir,
I'm using the sample application "channel_sounding_ras_initiator" to performing the evaluation. Here are my test environment: - Developement kit: nRF45L151 - Tool...
Hello,
I previously used DECT NR+ modem firmware mfw-nr+_nrf91x1_1.0.2 on nRF9151 DK Development kit and moved on using the new modem firmware mfw-nr+_nrf91x1_1.1.0.
But...
Hello.
This may be a basic question, but please let me know. I am using nRF54L15-DK and nRF Connect SDK v3.0.2.
Is the 32MHz crystal running when the nRF54L15 program...
hi everybody: This is my first time developing an nRF chip and also my first time using VSCode After installing nRF tools and fast (3.0.0), I found that I did not see the...
Hi there,
I am using an NRF54L15 custom board and am trying to set up a functionality using DPPI + PPIB. using a single in (1 event) and single out (1 task). I have two...
Reading from the FICR seems to produce some results other than what I would expect. For example, reading from offset 0x10C seems to return the flash size (instead of 0x110...
Hello everyone
i am using QFAB/DCconcverter reference layout to design my prototype, using the 3V coin cell battery as a power source .my question is in the reference layout...
Hi,
I tart using HID keyboard example, SDK 8.1.
If i turn off the ble of the ios device and then turn it on the nrf51822 is connected but it is not send the chars.
...
Hi, Nordic Engineer:
Would you like to give me some advice? On my hand, i have a slave ble device(not nrf51822, also i can not change the code). I want to run s120 softdevice...
i am able get the status of led of pca10001 board using usb dongle. now i have to make other pca10001 board as central and want the same data of it? Kindly help, i shall b...
We are planning to optimize the radio-frequency signal,so the some docunments like Simulation model are needed.which can help optimize the RF signal through ADS simulation...
In ble_advertising.c, line 165, you can see such interesting code. I assume it is a copy/paste error:
if(p_advdata->p_tx_power_level != NULL)
{
m_advdata.p_tx_power_level...
For the first, impressed by your intoducing NRF52 chip.
Question: what`s NRF52 indoor range using onboard antenna and maximum output power (+4dBm)?
Thanks.
Hi~
I am struggling to get the BLE packets detected by nrf sniffer (v1.0.1) using wire shark. Its only showing "ADV_IND[Malformed Packet]" periodically. I didn't understand...
I believe what I am asking is extremely specific, but keeping hope that I might get some direction
I have used a clone ST- Link v2 programmer to download code into a NRF51822...
Hi all,
I would like to trigger some actions on difference devices communicating with the ANT protocol based on the distance they are from each other. A simple example...
Hi
The documentation for the new feature in S110 v8 to change the gatt table size says that to change it the linker configuration needs changing .
This means it is a...
Hi all,
First of all thanks for Nordic team for the excellent support. It is very useful for a beginner like me to get started on BLE development.
I am using the nRF51422...
