Hi I'm testing the current consumption of the external qspi-flash on nrf5340dk [ MX25R6435F]. I have used ppk 2 to measure consumption with the dk and also have used a power...
Hi,
We are using nrf21540 in GPIO mode + mode pin ( and CONFIG_MPSL_FEM_NRF21540_RUNTIME_PA_GAIN_CONTROL) with an nrf52833.
We are developing under nrf connect sdk 3.0...
During the development of a Matter over Thread product, I encountered the following issue:
After adding two Matter over Thread devices (an OnOff Switch and an OnOff Light...
Hi Nordic Teams :
I would like to check the current consumption by BLE DTM.
1. Is the table measurement is from 3.0V input?
2. I find the condition in the datasheet...
HI ALL,
nrf54l15dk,v2.8.0,peripheral_uart demo and no changes have been made.
Then add the following content to prj.conf
sysbuild.conf
mcuboot.conf
At this...
I'm developing my application with nrf 52832 and nrf SDK v17.
I know NCS is more powerful. I'm currently learning how to use it.
But now.I still need my application with...
I'm writing a wav file from the nrf52840 board to the nor flash w25q128jv with a capacity of 16mb but it seems that I can only operate on the first 2mb, even when dividing...
Hello,
I am using the nRF51822 Development Kit and nRFgo Studio Version 1.17.03211.
I have compiled the blink_example and the s110 ble_app_hrs in the nRF51_SDK_v6.0...
Hello,
I'm starting a new project based on nRF51822 and I'd like to configurate the bluetooth to be appeared and allows the communication managment ( I want to creat two...
Hi All,
I'm using nRF24L01P for TX device and want to receive packet from nRF51822 RX device.
nRF24L01P TX device Register settings are as follows;
Reg.EN_AA=0x00...
I am trying to develop for some nRF51822 mbed boards, and I would like to use the S130 SD to enable both central and peripheral behaviour. The machine I'm using for development...
Hi All,
A simple one,, I just downloaded the master control panel app for android in android 4.4 phone.
My question is how to do bonding and how to delete bonding info...
Hi All,
I am testing the functionality of NRF24L01+ and for my purposes I have configured it as PTX, No Auto ACK.
I am able to communicate with the chip just fine and...
I am trying to send continuously sampled analog input using NRF24LE1 using Shock burst,The transmitter is not working while trying sample continuously.please help.
code included...
I'm using the nRF51822 eval kit
I have installed MCP but after starting I get pop-up: Master Control Panel has stopped working
In nRFgo Studio / Device manager pane...
Hello,
I'm designing an application where both, BLE and Ant should / could be used. I tried to download the S310 SOFTDEVICE from www.nordicsemi.com/.../nRF51422 . I'm asked...
the proximity example is running ok. but when I modify the length of the alert_level I have the following error on the server side that I am not understanding.
476;16:12...
Hi all,
I'm working with the nrf51422 and the nrf51822 and I was wondering what the current status of the over the air DFU system is.
I'm using SDK 6.0 and I managed...
I need a low latency stereo digital streaming device and the model (nRF24Z1) is going to be discontinued.
Has Nordic a replacement for nRF24Z1?
PD: i need stereo, so...
In our product we have both a DFU profile and an application profile which is confusing Mac OS X 10.9 "Mavericks" since it caches device services unless it receives a service...
Hello,
I'm a new developer on nRF51822 and I'm trying to make a program that allows the nRF module to communicate with a glucose meter and a Smartphone application. My...
I'm working with the nrf51-app-ble-lbs demo from github. I notice that when I'm using BLE scanning apps, the VS service UUID is long (128 bits), whereas if I'm looking at...
