Hi,
Now, I'm doing a project. A device node sends picture data and the other one receives these data. Then the receiver shows the picture on the SSD1306 display.
At receiver...
Nordic Support,
My product uses the nRF52840 chip and nRF52 SDK 17.1. I have a feature request to support hosting multiple peripheral connections, each with a unique advertising...
I am working with NRF52840 with SoftDevice S140 and SDK v17.1.0.
The boot loader address for this chip is 0xF8000. I can set up one of the 'fstorage' module with the address...
Hey everyone,
Does anyone here have experience with firmware OTA updates over the JIO NB-IoT network? The process seems a bit different since JIO Cloud always sits between...
Hello:
The latest nRF54L15 Errata for Rev 2 shows that the previously reported "GPIOs can exhibit radiated emissions" is no longer present in the Rev 2 SoC.
Can you please...
Hi, this is a very broad issue that i am having, because i dont know the source of it. I am simply unable to use the bme68x IAQ library. i have downloaded the external bsec...
Greetings!
I am using Wireshark along with an nRF52840 dongle to monitor BLE traffic between a mobile app and connected peripheral and periodically I see some "L2CAP Fragment...
Hi,
Please share nRF51822 observer mode power consumption profile plot to get complete power consumption during only receiving mode.
See below plot for advertising mode...
Hi.
I'm little baffled by the example. Out of box it doens't add the alert notification service to gatt service list in advertising init. Nor I cannot see it with nordic...
As i recently wanted to have a timer as a class member and a naive
class Foo {
APP_TIMER_DEF(my_timer);
};
did not work I started to look into the source code....
Hi,
I'm trying to configure the SPI by using the nrf_drv_spi. the problem that I'm facing is the configuration of the "spi_config.SPI_CPHA = SPI_CONFIG_CPHA_Leading" which...
Hi!
We are using ble_radio_notification for changing the advertisement data after every advertisement.
The problem is that it doesn't work, the device freezes when trying...
I have designed a custom PCB with Nrf52 for an ECG wearable sensor application and is trying to optimise the power consumption of the device. The application is to collect...
Hi.
I'm currently trying to scan beacons with timeslot example.
However, I found that there're more than 20% of loss while scanning beacons broadcast.
I think that...
Hi, I tried Adding another service to the LBS Program, but the chip is getting reset , i have another 16 bit uuid service with different base uuid, Its getting stuck at SOFTDEVICE_HANDLER_INIT...
hi
im using nrf51422 v2 with external sdk v6 with softdevice v7
im running one of example that its name is ble_app_template and when i run it , it show up for just one phone...
hello,
I want to change the advertise time out time by BLE_GAP_ADV_TIMEOUT_LIMITED_MAX.
Is there a problem with changing BLE_GAP_ADV_TIMEOUT_LIMITED_MAX to ex. 1000sec...
Hi,
I can use nRFgo Studio via nRF5x Bootloader to update application firmware(Hex file).
It look to be using "nrfutil.exe" to create a XXX.zip file and go through UART...
Hi.
I am on nRF52 DK (PCA10040 v0.9.0, s132 SD), SDK 0.9.2 and Linux (Ubuntu).
I am currently working on the SDK's example ble_app_uart.
I am only using gcc, and...
I was working with examples/ble_peripheral/ble_app_gls. In the SDK11alpha configuration, I paired the dev board with my Android phone running nRF Toolbox and was able to start...
