I'm not able to debug any of example applications that uses non secure build. Non ns versions works fine. I have added CONFIG_TFM_CMAKE_BUILD_TYPE_RELWITHDEBINFO =y to my...
Hi Team,
We recently received our custom PCBs and are currently trying to configure pins P1.00 and P1.01 as UART0 RX and TX respectively. However, the UART communication...
Draft — ready to post on Nordic DevZone / Zephyr mailing-list
Title nRF5340 DK + MCP2515/TJA1050 module — can_start() always returns -EIO even in loop-back
Hardware...
Hi We are working on setting up CI/CD pipelines for our nRF application. The application is set up as a stand-alone application with its own west workspace. It uses external...
Hi ,
1.In the example: In nRF5_SDK_17.1.0_ddde560_usbd_msc_1\components\libraries\block_dev\qspi\nrf_block_dev_qspi.c, I need to set the following 0xB7 bytes. How should...
Hi I'm testing the current consumption of the external qspi-flash on nrf5340dk [ MX25R6435F]. I have used ppk 2 to measure consumption with the dk and also have used a power...
Hi,
We are using nrf21540 in GPIO mode + mode pin ( and CONFIG_MPSL_FEM_NRF21540_RUNTIME_PA_GAIN_CONTROL) with an nrf52833.
We are developing under nrf connect sdk 3.0...
Hi:
I develop my project with gazell, Device can keep send to host,but host can't keep send to device(I'm not mean for host sent ack to device).
In my program, I use "nrf_gzll_add_packet_to_tx_fifo...
In the nRF52 reference design, not using the DC-DC converter would result in higher power consumption. By how much? Any documentation regarding the details. Thanks
Hi all,
I am new in nRF51822. Today I am doing experiment using GPIO and radio transmission.
I wrote a very simple code as below:
int main(void)
{
init_clock();...
Hi, I've got a serious problem in my project. Some of its features require hard timings. The usage time of these features is longer than the single timeslot and I must be...
Hello guys, I'm doing a hobby project and can't seem to get it working. Aim of the project is to transmit temperature values from a DS18B20 using an Arduino Uno and NRF24l01...
I'm experimenting problems with a nRF51822 custom board. Recently I managed to run the blinky sample project. Now I'm trying to test a BLE project, but I'm having problems...
Hey All,
I am currently trying to have a Analog Signal come in through P0.05 which then gets converted via the onboard ADC and send out a Service Characteristic. I am using...
Hi,
I am using your NRF24L01P-R7 part .Can you please specify its maximum distance upto which it can detect other TAG in open area when there is no wind at normal atmospheric...
I have a question about PXP profile. Could I use the nrF52 (S132) Nordic's PXP example to dynamic change TX power when I have bonded or connected Android phone device ? I...
I try to implement a BLE vendor service that has some characteristics. When I bonded the nRF devive (vendor service already download to device) with my Android phone and then...
Hello All,
I have modifies the Spi Master code to communicate with an ADXL345 Accelerometer. I set up my powermode and the percesion in the setup phase. However, when I send...
Hello, Nordic Team.
In my program, I have to change the value of the characteristic before start. I write:
case ACI_EVT_DEVICE_STARTED:
g_aci_state.data_credit_total...
Hello,
I want to make my Arduino coupled with the nrf8001 advertising a simple data (an integer). There should also be a possibility for dynamically changing the advertising...
I have a Jayconsystems breakout board for the nrf8002 bluetooth chip. Nothing is connected to the breakout board and the chip is unprogrammed. My current meter reads 6.0 mA...
