After I get a Disconnected() event, I want to start scanning again, therefore try to call StartDeviceDiscovery() again.
IsDeviceDiscoveryOngoing was checked before.
The...
Hi, I wanted to ask a question regarding sending data.
I currently have external memory that will send out serial data (SPI) to the nordic microcontroller. I have saved...
Recently, I try to programme nRF51822 DK communicating with nRF2401e1 DK,unfortunately，which does not success. With setting radio configuration: TXPower,frequency channel...
E:\BLE\work\nrf51_sdk_v6_0_0_43681\nrf51822\Board\nrf6310\s110\ble_app_hids_keyboard
SDK 6.0.0
Softdevice 7.0
When I connect to Android 4.4.3 device(Nexus7 II) will...
E:\BLE\work\nrf51_sdk_v6_0_0_43681\nrf51822\Board\nrf6310\s110\ble_app_hids_keyboard
SDK 6.0.0
Softdevice 7.0
When I connect to Android 4.4.3 device(Nexus7 II) will...
I have been trying to understand and get the “ble_app_template” running this weekend, but I keep running into errors. For example in
static void sys_evt_dispatch(uint32_t...
Based on the nRFUart demo, I added a masterEmulator.DiscoverServices() block before the DiscoverPipes() block in a very similar manner. Purposed is to be able to get more...
Hello,
I have been going through devzone questions to figure out how to enable the default debugging messages through Putty for the ble_app_proximity example project from...
Hi:
I make the gazell ready, and I need an extern PA(RFX2401) for a long distance commuicate. But there is some trouble when enalbe the PA.
My function:
Host:
pin_Set...
Hello,
I am using ble_app_multilink_central example as a foundation of my app involving central - peripherial connection (S120 - S110). My app works nicely but i have problem...
Hello, I am trying to establish a connection between the nRF52 board and the USB serial converter TTL-232R-3v3.
The setup is such that I connect the converter cable to...
Hi all,
we have a project based on nRF51422, SDK 6.1, Softdevice S310 2.0.1.
We use the bootloader for DFU services. Our problem is to send a service changed notification...
Dear all, I had debugged example Heart Rate Service from SDK 9.0.0 without problems but I think we have a exception, when I insert a breakpoint on line 923 instruction APP_ERROR_CHECK...
I am trying to use the scheduler, but I would like to know if it is possible to have events with different priorities... As an example:
Task A - Priority LOW
Task B -...
We designed our own board using nRF8001 and EMF32, I used the EMF32 development kit to test the code and it is working fine. When I down the same code to my own board, it...
Hi ,
I am planning to implement S120 UART to communicate with desktop as well as S110 UART BLE.
I browsed in the forum and found out we already have example in github...
I have a small nRF51822 module that I want to use for UART communication without handshaking, and I'm having problems with reliability. Basically the nRF51822 crashes and...
Hi, I've got a pretty basic question, but I haven't found a satisfying answer for it. It is obvious, that the CC registers are 32 bit wide, but because the RTC Counter is...
Hello:
Does the nrf52 radio peripheral EasyDMA write to PACKETPTR on byte boundaries or does it write "bits"? Suppose I have the ADDRESS_BCSTART shortcut enabled and the...
Hi all,
I can use the API sd_ble_gap_rssi_start to start RSSI and can get the value when the BLE_GAP_EVT_RSSI_CHANGED event occurs.However,when I use the sd_ble_gap_rssi_stop...
