I'm looking into a rare issue on the BBC micro:bit V2 which uses the nRF52833 as its (application) microcontroller. I used to be familiar with some CPUs from the 80s but my...
I have shifted from silicon labs for BLE project. In Si labs we have burn BLE bootloader and BLE application separately. Do i need to do the same here in nrf controller? If...
I am unable to detect any i2c device when connected to the Nordic nRF54L15 DK kit. I have change the voltage from 1.8v to 3.3v and Tried and explore other pins in Port 0 and...
Hi All,
I have to implement an I2C Slave on my nrf52833 BLE project which is currently working (SDK 2.9.2)
I need some confirmation with the following step:
I have...
I am using the 54l10 chip, and after compiling the project, I will receive a hex firmware and a zip update package. The bin firmware and hex firmware in this update package...
Hi,
I faced with an initialization issue of combination two features: MCUMGR and UART_ASYNC_API. I get a crash right after the FW starts. It looks like the SW configuration...
Hello, I need to configure and compile a sample to send an audio stream (mp3) to the I2S interface.
I tried to put together some configuration from other samples but no...
Hello.
I need to hold 64-bit timer value. I store the 32-bit hardware timer value in one variable (low DWORD) and use an additional uint32_t variable as a an upper part of...
Hi, I'm having a bit of trouble getting the broadcast or HRM example to work. I'm using crossworks and after my last question, removed the retarget.c file and the code compiled...
I am new to smart beacon. We have to make a demonstration of our product i a short time. But I could'nt make it run. There are so many sosftdevice, bootloader and application...
Hi,
Basically, I have a DAC 7562 chip with inputs connected to pin 0.17(SYNC pin), 0.18(SCLK pin), 0.19(TX/Din pin), 0.13(CLR pin), 0.14(LDAC pin) with outputs connected...
I just recently upgraded to SDK 7.2.0 and am now using the keil pack installer as well. First of all, I really appreciate the ease of this new system, but I'm running into...
The new softdevice v8 states that previous revisions(1 and 2) don't support all the new features, and I'm curious how to determine what revision my ic is.
thanks,
akbar
Hi
I have recently purchased an Adafruit Bluefruit LE board ( www.adafruit.com/.../1697) , that uses the nRF8001 chip, so that I would be able to send iOS notifications...
I have a new nRF51822 kit, and although I can (apparently) configure the beacon, it always shows "Beacon not found" when I try to use it.
I'm using an iPhone 5s and the...
Hi, I got new NRF51-DK and dongle with 51422 chip.
It seems that the layout of the memory map has changed with the new SDK and I can't find any information how it should...
After I uploaded hex and dat file which is compiled from sample beacon source code in SDK to nRF51822 Beacon Kit via nRF master control panel app, I got Upload failed GATT...
I have done some testing and debugging, but I can't seem to get the nRF51 DK working with the beacon example project.
I used the keil v5 pack installer to access the ble_app_beacon_s110_pca10028...
I've noticed that the L2 value has been changed from 10nH to 27nH in the reference layout and on the new boards (DK and Dongle). This value is only for LDO setup (from PS...
Hi,
If we set the prescalar for RTC1 to 0xFFF (i.e. max value allowed), tick event is getting generated every 125msec.
Using the below configuration i started a timer...
