Hi all,
I'm trying to use uart2 on my custom nrf9151 board, but I'm stuck. As I understand, I use i2c1 so I can't use uart1 and i2c1in parallel, so here is why I wnt to...
Hi - I am seeking clarification on a topic as I am a little unsure on the correct way to do things.
I'm using an nRF52840 and porting an old Firmware from nRF5 SDK to NCS...
Hello,
I'm moving my project from SDK1.9.1 to SDK3.0.2. Project is based on peripheral_uart sample (UART part is removed since it is not necessary).
I have encountered...
Hi, i'm using NRF5191 with DECT.
DECT modem: 1.0.2
App: hello_dect sample
In datasheet I found that NRF9151 support various band: 1,2,4,9,22
and I'm using these value...
Hi there,
on the nRF5340 Audio DK, there is a FT2232H, which provides FTDI_SPI + FTDI_SPI_SEL.
How this can be used, is there any sample for this available?
And how...
Hi
I have some questions about nRF5340 & nPM1300 decoupling cap
nRF5340
1.For pin A3/D2/H11/K1/L5/L11, ref. SCH is 1uF*1 and 0.1uF*5, could we only connect 1uF*1 and...
Hello,
I have a product based on nRF9160 that uses GNSS. The device is a meter, not an asset tracker, so GNSS is not the TOP 1 feature we need.
When the device is installed...
What are the correct PTX and PRX configuration settings for using dynamic payloads with auto ACK disabled? Can I just clear EN_AA and set EN_DPL and DYNPD for the pipe I'm...
Hello! I am working on a project in which I want to send stored sensor data to a smartphone whenever the phone is in range or at specific times of day.
Most of the communication...
Hi,
I am trying to get hold of version 2.1.0 of the dev kit for use with the sniffer. The dev kit is in stock at Mouser but they can't confirm the version number, but said...
I have developed the schematic of connecting NRF 8001 BLE chip with Arduino,the file is attached that contains the schematic. Can you please verify my schematic i.e will it...
Hi, I'm looking for a solution can make a ble device communicates with multiple 2.4g devices at the same time , is 51882 qualified for this? or just by combining both nrf8001...
Hello,
I would like to use the fifo common library but i have an link error. I don't understand that because fifo_app.h is included and contain the functions...
...
Hi
We are using indication to send data to make sure master receive all the package.If we didn't
receive the confirm message,what should we do?Should we send it again in...
I'm guessing it is because the engine powering the site does not support it. But has it ever been considered?
I think it is a powerful way to engage users and build a community...
Hi,
I have two questions about nRF24LU1+.
Q1
Can i change nRF24LU1+ isocheonous endpoints(Endpoint 8 IN/OUT) to Endpoint 1 IN and Endpoint 2 OUT?
Q2
Can i use Endpoint...
Hi,
we’re a group of students at NTNU in Trondheim doing a project regarding bike and pedestrian registration. So far we want to make a solution based on iBeacon and Bluetooth...
Hello,
I am looking into the possibilities of implementing frequency hopping using the nRF24L01+ radio with an external Ti MSP430 microcontroller. I have read that it's predecessor...
Hi,
I want to realize the function of bond, I use "lib_aci_bond(180/* in seconds */, 0x0050 /* advertising interval 50ms*/);'\",.When I click the connect, it can connect...
In nrf51_sdk_v4_4_1_31827\nrf51822\Source\console\console.c,
#include "uart_legacy.h"
But there is no "uart_legacy.h" file in the SDK.
I have to modify to "app_uart...
I downloaded the source for the Android UART app, hoping to hack it into something I can use to test my gadget. But it's incomplete: it fails with the message:
Missing...