Hi! I am building an android app for my project. I am using Proximity , UART and DFU from nrfToolbox app. I have 3 buttons on my home screen dedicated for each of them. I...
Dear Nordic employee:
1、 what do I have?
I have a thingy52 develop kit（nrf52832）
2、what is my purpose?
the quality of thingy52 audio demo is not good（iphone7）...
Hello Nordic,
My development environment:
SDK>> NRF51822_SDK10, SoftDevice>> S130
Example>> ble_app_uart
I am looking forward to your reply!
Thanks.
Best Regards...
Dear friends,
according to "nRFConnect_BLE_User_Guide_v2.0", to set up a local device,i should complete the following steps:
Connect a development kit or dongle to...
Hi
I have add some function call like sd_ble_enable in mesh example, I test to get
then I set the address and all sd_ble_cfg_set is ok
but when I call "sd_ble_enable...
Nordic \ nRF5_SDK_12 nrf52832 using 2.0 _f012efa \ examples \ peripheral \ pwm_driver, pwm_driver example
Want to set up two road PWM phase is different, for example, the...
I'm using nRF52832 and S132 based on nRF5 SDK v14. I get a error code 4 when I add DFU service refer to the experimental_ble_app_buttonless_dfu . The SDK has changed so much...
Hi, I am trying to change the beacon data.
I changed Beacon UUID already, but I can not find where can I change device name.
I guess I need to change the gap_adv_data...
Hi,
I am upgrading to SDK 6.0.
What function should I use for retriving the whitelist data?
SDK 5.2:
//err_code = ble_bondmngr_whitelist_get(&whitelist);
//APP_ERROR_CHECK...
I'm reading the source for the nRF Toolbox app for Android 4.3 and comparing it to the Proximity Profile spec from the Bluetooth SIG, which has this to say about path loss...
Hi,
How to implement the static PIN type pairing, when the server device doesn't have keyboard or display? Our requirement is, Master will initiate the pairing process and...
Hello,
I have downloaded the software related with the "nRF51822 Bluetooth Smart Beacon Kit" in order to modify typical iBeacon's parametres such as UUID, Major ID, Minor...
Hello,
I am trying to implement a Time-On-Air measurement with two nRF24L01+.
I set up the devices to work at 2Mbps, 3 bytes address, 1 byte payload, 1 byte CRC.
Both works...
I'm using the nrf51822 evaluation kit. There is low level access (via memory registers) the the 2.4Ghz radio in either a Nordic proprietary protocl mode, or Bluetooth LE mode...
Hello Nordic Semi,
We are using the nRF24L01+ for a remote switch application. We have a small transmitter button (nRF24L01+ layout as per datasheet with micro controller...
I have a problem within the following szenario:
I transfer data from my nRF51822 Peripheral to a connected Central (Android App) as a bunch of Notifications with maximal...
my project can't goto sysoff mode, (desktop2)( project based on mouse demo)
m_prw_mgmt_set_sysoff_timeout(DEFAULT_BTLE_INACTIVITY_DISCONNECT_PERIOD);//can't sleep here...
DEFAULT_BTLE_INACTIVITY_DISCONNECT_PERIOD is 3600//one hour
i can't wakeup if disconnect'time over one hour.
but i can wake up form com_event_advertising_timeout
my code...
Hello,
i would like to know if the new SoftDevice 130 for the nrf51822 is compatible with the DFU OTA bootloader example provided in the SDK (nrf51822/Board/nrf6310/device_firmware_updates...
Can I get uuid of central device from peripheral device(nrf51822) ?
I want to check out which smart device is connected.
May be I can tell central is iphone4s or iphone5...
Hi,
I am new using nRF51822 DK with the nRF6700 Starter kit. Downloaded nRF SDK and got most examples running fine including BLE examples with s110.
What I would like...
