I am using the nrf5340 on a nrf7002fk dev kit. I am interested in low power operation so I am measuring the power consumed.
I am running a simple app:
int main(void) ...
Hi,
I have a simple question about Bluetooth Channel Sounding:
Question: If I use BT_CONN_LE_CS_MAIN_MODE_3 as main mode (PBR + RTT), does it make sense to use sub mode...
Hello Nordic Team,
I am currently working with the NRF54L15-DK. I have successfully configured the simple ADC on AIN4 (P1.11) and am able to read the raw sensor values....
i am writing data from wav file to w25q128jv and i got error -22 at some offset while writing. i tried many config but it seems the problem is not solved, does anyone have...
Hello Nordic Team,
I am currently working with the nRF54L15 DK and interfacing an occupancy sensor over UART. In my standalone application (non-Matter), the UART communication...
i am working on custom board nRF52840 with display ST7789 + touch Ft6336
1) i want to use LVGL library with Display how do i get started with LVGL .Any tutorials or sample...
Hello, this is probably a very beginner question but I don't know how to configure interrupt for the GPIO headers on the nRF52840 dev kit. I tried to search in this forum...
Hi,
I'm trying to flash the S110 onto my nrf51822 SoC, but nRFgo gives me the following error. (Also, hitting recover just gives me an error: "an error condition was detected...
Within app_button module, code for app_button_is_pushed() seems to have changed from SDK version 5.1 to 6.0. I notice my code has stopped working properly with that update...
Hi
Now, we are planning to implement an ANT+ RX (slave). I checked nRF51422 product spec. Radio current consumption is 12~13mA if receiving data between 250kbps and 2Mbps...
I'm using the boot loader that comes with the beacon development kit and I want to change it so that when the application software is running it can restart the device in...
I have managed to get the SPIS block working using standard sets of read and transmit buffers. This all works.
I am now trying to use the ORC register to send a single...
I am wondering how you put the nrf51822 chip to sleep. I've determined that the way to do this with the soft device is sd_app_event_wait() in the while loop. What about non...
Hello
I've been trying to create a simple BLE observer that outputs the nearby devices data onto the serial port using a PCA10001 board.
For this, I'm adapting the code...
Hi - I'm using the 51422 dfu bootloader from the nrf 6.0.0 SDK and it works fine with the iOS apps, I can send both .bin and .hex files to the device and it works fine. However...
Hi,
I am using nRF51822 evaluation kit. I want to develop GPIO isr (GPIOTE_IRQHandler) which can handle multiple GPIO interrupts. I have tried to enable the GPIOTE_IRQHandler...
Hi!
When using bootloader, I cannot update application data from Keil (for example for debuging), because after restarting bootloader is loaded and
!bootloader_app_is_valid...
Hi,
I have been using nRF51822 with my Android app using Android's Bluetooth Low-Energy APIs.
In order to get more details, I am currently working on integrating the Android...
EDIT:
I'm using nRF51422-QFAA E00 and S310 v1.0.0, SDK - nRF51 5.2.0.
I'm starting HFCLK from externall crystal for ADC conversion. Since I have no SD enabled everything...
I was using the sniffer to get a trace of the ble_proximity example for the NRF6310 DevKit, and noticed some Attribute errors when the Master Control app attempts service...
nrf51sdk v5.2.0
I am adding ANT service to our BLE application
To begin i building the BLE application and bootloader with the s310 softdevice.
I have modified keil...
Hi,
I have updated my nRF51-SDK to the latest version 6.1.0. I'm using PCA10000 dongle, nRF6310, PCA10004 and Master Control Panel for Windows. I've programmed my nRF51...
