Hi,
I would like an nRFX example on how to set up DPPI using single in (1 Event) and multiple out (2 Tasks). I have previously done this using the fork functionality in...
Hey all,
Every time I flash, I get the following error message:
Error: One or more batch tasks failed: - [Probe] Device error: Memory access error at 0x00000000. Probably...
Hello everyone,
I would like to learn how to create unit tests using the ZTest framework for a Nordic sample project, in order to better understand how it works.
I am...
The VSCode nRF Kconfig extension has very high cpu usage (2 cores at 100%)
When disabling the extension, the cpu usage drops back to normal.
I see the following in the...
Hello,
Yesterday, I received a new Power Profiler Kit 2 device directly out of the box, and unfortunately, it is not detected by any PC.
Symptoms: - The green LED blinks...
We are using the nRF5340 and our use case makes full use of all 4 shared peripherals for SPI and TWI as well as SPIM4. We want to add UART over USB and I was able to port...
Hello together, Which configurations or setup on the side of the Nordic nrf9161 DK has to be done to use the DEBUG IN connector for SWD? The board is powered by the 5VIN pin...
I'm attempting to write software onto a newly purchased nRF52840 dongle using nRF Connect for desktop, but I'm unable to do so. My environment is Ubuntu 24.042 LTS. The LED...
Hi,
I am working on a sensor device that requires very accurate timing on the sensing and sensor signal algorithm side. This device needs a low latency and low jitter radio...
Hi, I'm a novice in embedded systems. I have board based on nrf52811 and firmware written for my device but when I received my board from production I could not load firmware...
I run the system_off example without the system actually going off, by removing all the calls to start the system_off worker. Instead of going to off, I let the system enter...
Hi all,
I'm modifying the Matter Light Bulb example from Nordic's nRF Connect SDK to integrate I2S audio output on the nRF5340 DK. The goal is to play a continuous beep...
Hi,
I am working on zigbee demo "light_switch" with NCS2.8 Add-on SDK.I enabled MCUboot according to the steps in the course " Lesson 9 – Bootloaders and DFU/FOTA "
1...
I'm trying to use an ILI9341 display with nRF52840 in Zephyr (v4.1.99). The build fails with multiple errors about missing Devicetree properties when compiling display_ili9xxx...
Hello,
I have a legacy project that is using nrf5 sdk v17.0.2. I need to add the BLE DFU functionality to this project based on the nRF52840. Are there any examples on...
Hi,I am using NRF54L15 DK in which I need to transmit audio data over BLE where that data will be used for only plotting in application,I am using sampling rate of 16000 and...
I have been trying to use the Nordic security backend with the MQTT library (TLS transport). However, after I finally got everything to build , I am now getting runtime errors...
When calling the bt_conn_le_create_synced function to create a connection to a peripheral, which is synced to the PAwR train, I get a CONNECTION FAILED TO BE ESTABLISHED ...
I am using 2 nRF528400DK boards. Each board has a unique BLE Mesh sample loaded. The samples were made by modifying the default mesh sample provided by zephyr. One sample...
Hi support
I am developing code for the application core on the nrf5340 and testing this on an nrf7002dk dev kit. I am using sdk version 3.0.0. The code needs to read from...
Hi, How I can use/install nRF Util software ( device, nrf5sdk-tools, etc ) in a lab without internet access on MacOS machine ? I can download ' nRF Command Line Tools' but...
I have been testing nRF7002 in STA mode and in monitor mode. Both work fine - but is there a way to have both of them at the same time? Is this a feature that can be implemented...
