I'm trying to use the ADC and internal reference to measure battery voltage on the nrf51422, while S210 is enabled.
From the example nrf51-ble-app-temp-master, I found...
I have Nokia Lumia 630 and it works well with nRF51822-EK but only with SDK nrf51822_v5.1.0.36092 and SoftDevice 6.0.0. Now I decided to try DFU OTA. I programmed bootloader...
Hello,
I found that there is a multiprotocol demo in folder Board\nrf6310\s110\experimental\ble_app_multiactivity_beacon,then I found it can implement concurrent connected...
Dear Sir
We got the problem on DFU upload firmware, it always failed in second DFU . We must unpair the device at iOS setting panel. Before next DFU.
Here is the log data...
Hi All,
My requirement is to read the data from nRF51822 device that is connected to a bluetooth and bluetooth is connected to a system using a .Net application.
I have...
Hi everyone,
I'm using the nRF51822 (pca10000 Dongle + pca10005).
My plan is to send one byte over the radio.
I tried to use the SDK-Example as a template but it's...
Hi,
Is that possible to run the radio_test_example (\nRF51 SDK_v5.2.0.39364\Nordic\nrf51822\Board\nrf6310\radio_test_example) on the nRF51822EK? If yes, what modifications...
Hi!
I'm migrating my development environment to arm-based Mac. I succeed to install nRF Connect for Desktop app for aarch64 architecture, but struggling to get Bluetooth...
Hello everyone,
I'm working on an NRF54L15 DK evaluation board and I need to use NFCT pins as normal GPIOs. I found out here that I should define CONFIG_NFCT_PINS_AS_GPIOS...
Hi,the Nordic team.
I am using nrf54L15 to develop Matter. I have seen that the official sample programs are all equipped with external flash. How can I run Matter programs...
Hi,
I'm using an ISP2053 (nrf5340) chip on a custom board and debugging using the nrf5340dk. I'd like to use P0.02, P0.03 as part of an SPI bus.
I set up a simple experiment...
Hi,
I am programming with nrf52833,ncs v2.9.0,generating peripheral_uart to peripheral_hid_keyboard sdk.
And now with working serial times,err happend and log is Not able...
With the transition of the RTC peripheral on the nRF52, nRF53, etc series to the GRTC peripheral on the nRF54L, it appears there is no longer any low-power counter that can...
Background
Our device uses the CONFIG_LTE_NETWORK_TIMEOUT option from LTE Link Control, which by default is set to 600 seconds (10 minutes). I haven’t found any specific...
Hi:
I don't receive any messages in the console during any of the exercises in Lesson 3 and Lesson 4 of the nRF Connect SDK Fundamentals.
No errors occurred during the...
Dear,
I’m experiencing an issue with performing DFU over BLE Mesh. I have a setup with one node acting as provisioner and distributor. This node has a new image loaded ...
I am using nRF Connect SDK v2.4.0 and an nRF5340 DK set up as a PAwR advertiser. Is it possible to specify the channels to use in the Periodic Advertising train? I found the...
Hello everyone,
I am currently working on implementing the flash protection feature for the 54L05 chip. My objective is to safeguard the code storage area from unintended...
Hi
I am currently working with my project with 52840 and i am using sdk v3.0.1 & toolchain v3.0.0 to develope.
I am learning how to use DFU over UART from the application...
Hi all,
I am using and nrf9160, in particular a thingy91. It is running 1.3.7 firmware. I have the SLM sample loaded and can sent AT commands to the device using the nRF...
Hi
I am looking at this information:
https://docs.nordicsemi.com/bundle/ncs-latest/page/zephyr/samples/subsys/fs/fs_sample/README.html#fs
I created the sample application...
