This system does not work if I enable the third Pipe (Pipe2) .
The system is working without any problem as one RX and two TX (Pipe0 and Pipe1).
The problem on enabling...
Hello,
i have read if not all posts about writing to FLASH while using BLE. But could not find the desirable method.
What i would like to do is to write to flash from...
Hello,
i have read all posts about writing to FLASH when using BLE. But could not find the desirable method.
What i would like to do is to write to flash from characteristic...
I'm trying to add the product key it shows an error "can not the product to your list" and therefore i will not able to access to the User guide
Thank you
hello, im from india im using nrf24l01+ for my project to transmit and receive data between two arduinos. i tried all tutorial basic programs but i cant sucessfully send and...
I'm analyzing app_timer scheduling code..
I have an question about list_insertation_handler function in SWI0_ISR
I think if ( (p_timer->ticks_at_start - m_ticks_latest...
I would like to test the newly added v4.2/v5.0 Bluetooth features (e.g. LE Secure Connections, Data Packet Length Extension, 2xSpeed, etc) against non-nordic devices. I have...
Hello
I'm using the nRF51 DK and I have a UART over BLE link set up between the board and a phone with the nRF UART app. I'm trying to get the board to execute a particular...
Hi,
I'm using nRF51 Development Kit to program the beacons. I've connected the beacon just like it's described in the last update of this thread using the 10-pin adapter...
Hi,
I just noticed that the nrf51822 doesn't have an eeprom and I already had the pcbs done. Can I use the NVMC to write USER data on the CODE (is it flash memory are?...
I am trying to do over-the-air (OTA) device firmware update (DFU) on a device with bootloader same to the "dfu_dual_bank_ble_s110" example in the latest nRF51 SDK . On the...
Hello there guys i been reading your 100 pg PDF for awhile now and im yet to understand or realize how is it that i add/place/create a payload or data to send/Tx via Master...
We are using Gazell to stream data at <=6mS intervals for very low latency wireless gaming peripherals. We'd like to have many of these peripherals devices (more than 24)...
Hello
I'm trying to get a SPI master onto my S210 programmed nRF51422. I'm using uVision 5 and have all the nordic packs installed and built off of the ant broadcast tx...
main.c
I am trying to talk to this sensor: www.meas-spec.com/.../MS5803-05BA.aspx via SPI... it quite seems to work as I get expected responses to commands but as the title...
Do the Nordic Boards offer some sort of config region where settings like the Bluetooth address are stored? I would like to change these settings without having to recompile...
I am trying to set up a GZLL star network on the 51822. I understand that a single GZLL host can support up to eight devices but whenever my host attempts to communicate with...
Hi Team,
Is there any example to understand Prepare Write Request/Prepare Write Response?
In ble_uart_app example, I am getting p_ble_evt->header.evt_id = 2 if I put...
I am using S110 v8, But I am having this problem since the very first stage of developement, so earlier versions of S110 also.
The problem is that sometimes I am advertising...
I'm running: SDK 7.1, PCA10028 eval board, SD310 2.0.1, MCP 3.8.0.7
I'm trying to get Notifications to work. I have two attributes. I write to one and have it update the...
Hey I'm developing a sensor network using ANT shared channel. Here are my set up:
I'm using a Android tablet as master. The app was modified from aquired channel app...
