Hi,
I'm using nRF SDK 16 for my application on the nRF52840 custome board. When I set both parameters (i.e., support for coded PHY and 1M PHY ) in the scan initialization...
Hi all,
I'm working on a Nordic-based system involving multiple nRF52-series chips exchanging high-rate sensor data over both radio and SPI links. The setup involves two...
Howdy!
I am attempting to develop a system using an nRF52840 and an ADS131M04EVM (ADC). Our application requires us to collect data at a high sampling rate (>= 16k SPS...
I have a nrf9160 DK but when upload SLM application to it i can not send AT commands to it over it's usb port but in asset tracker application it works i want to modify SLM...
Finally we got our prototype boards and proof of concept firmware code done and we are a bit stuck on the average power consumption over time for the entire sensor that is...
We are implementing a Joiner device using OpenThread on the nRF5340 (with Zephyr, NCS v3.5.99-ncs1-4). After successfully joining the Commissioner's network ("Join success...
Hi,
I have integrated Neuton’s “Transport Type Detection” pre-trained model into my firmware, running on a nRF52840dk. For collecting 9-axis IMU data, I’m using the ST X...
Hello,
the mass production firmware of our product was generated on NCS 2.2.0 (MATTER 1.1). Now, we are attempting to OTA upgrade our product to the firmware based on NCS...
When dealing with low power access via NTN (via Skylo), is there any limitation about any particular use of SW?
Like, is Zephyr or other RTOS combinable with the Skylo certified...
I'm trying to flash a XIAO nrf52840 following the instructions for flashing with UF2 but it won't seem to work. After I drag and drop the zephyr.uf2 file in the mounted drive...
Hello. I am trying to implement stable connection between my nordic nrf5340 and Samsung Galaxy Buds3 earbuds. I did it based on ble audio example with two connections (one...
I have a 7002dk dev kit. Currently for evaluating the nrf5340, which will be used in my product. Currently i am trying to evaluate if it is possible to use the nRF5340 USB...
Hi,
I am using two nRF52833 DK and both are connected with nRF21540.I notice that when I have a very high throughput, never stop sending 244 bytes, I will notice that average...
Hi,
I would like to ask about the future plans for Zigbee development, as the current situation is a bit confusing.
From what I’ve observed, Zigbee R22 has been deprecated...
My team recently acquired two NRF24 transceivers to use on our drone project. Personally I've used NRF24 modules before and have successfully paired them with Arduino and...
Hi all,
i just received 2 nRF54L15-DK boards. Both I am not able do program - I tried:
1. nRF Connect for Desktop
* I did not make any change on the board afre unpacking...
I want to use the boards NRF-5340DK or NRF-52840 with the external host for the channel sounding feature. Can we use the feature on the mentioned board? If so, can you please...
I'm trying to send and receive an extended advertisement packet with about 100bytes of payload.
I started with the sample extended_adv example.
I 1st validated that using...
Hello. We are updating firmware to use nrf sdk 2.9.1 (from 2.5.2). Below is my proj.conf, should I expect any breaking changes?
############################
# Stacks...
Hi,
I want to configure the nRF9160's internal flash storage_partition, it has 32KB currently, I want to change it to 100KB. How to do that? Using nrf9160dk_nrf9160_ns.overlay...
As the title suggests, I want to use west build without having to include the BOARD_ROOT parameter.
I have already referred to this link , but the results were not as expected...
Toolchain v2.70, SDK v2.6.1, VS Code, Windows
Code derived from UDP sample works on DK board but fails on custom device.
Device is using DK board configuration, but no...
