I've been unsuccessfully trying to serialize BTLE example programs by SPI. I have two PCA10028 boards and I'm using SDK10. In addition to serialization examples, I've tried...
Hello,
Connection between linux router and NRf51 devices worked before I've updated kernel version from 4.09 to 4.3.
Now, with the same configuration and hardware, I'm not...
Hello,
Connection between linux router and NRf51 devices worked before I've updated kernel version from 4.09 to 4.3.
Now, with the same configuration and hardware, I'm not...
Hi
Does anyone know a CE—certified module based on the nRF24LU1+? Ideally, it should have an SMA connector, but any kind of antenna would be fine.
There are many modules...
I am running peripheral example radio test example on PCA10001(part of nRF51822 Evaluation Kit). using nordic sdk v7.
I am using mincicom on linux at baudrate of 38400...
Hello!
I am trying to get windows phone work with nrf_uart example on nrf51 dk board (pca10028).
I am using SDK 9.0 with S110 softdevice ver. 8.0.0.
I was using examples...
Hi
I met a problem when I use my new board,I found that the example in the peripheral folder in SDK can run correctlly,but the the example in the ble_peripheral folder...
Hi, I'm trying to use the example bootloader with the new NRF52, everything seems to work fine except that I'm unable to bond to the device when the bootloader is installed...
I sniffer the packets when I use a phone to connect to a BLE device.
However, in the packet with CONNECT_REQ label, the source address (init address) is not the bluetooth...
Hi.
I'm trying to communicate with legacy nRF24L01P using nrf51822.
I received packet from nrf24l01p, but I can't send information back.
The data I should send is more...
I use the persistent storage manager for saving some calibration parameters. It seems to work ok - I can power off/on, and the values are still there.
However, after I...
Hi. I would like to get into bare metal programming, and have decided to go for ARM processors. Are there any ns-kits or courses availible for purchase?
thnx in advance...
I have a few questions regarding power-fail comparator (POF).
How much current POF consumes? About the same as low power comparator (0.5uA) or lower?
How will softdevice...
Hi,
my firmware works fine, but when I tried to do DFU using the master control apk, it would get to the download screen and then quit.
This is the text:
DFU version...
I wonder if I can ask about the leds intensity control:
I need to control the led intensity without the PWM because I'm using the softdevice & PWM didn't work with it,...
Dear All,
I'm trying to set a static passkey. I have created 2 custom characterestic. One characterestic is used for notifications and the other one for writing. For communication...
I'm making a peripheral device that should be powered off most of the time, but never idle if on, so I want to make sure that it is always (1) connected, or (2) advertising...
Now I have a project to build the schematic.
a, 5 LED indicators(0603) were driven individually by GPIO port directly, serial with resistor, then pull down to GND.
Is...
I installed nRFgo Studio Version 1.20.0.2 (which removed my older version) and was trying to program a softdevice (5.2.1) into our custom board and was presented with a popup...
Hello, I just received the nRF8002 development Kit and want to connect it to my windows 8.1 64bit machine. I get errors that there is no driver. Tried downloading the latest...
Hi, when calling sd_ble_gap_address_get from APP i get 0xXXXXXXXX4F and when i call it from DFU i get 0xXXXXXXXX50(X beeing the same), why is this? Is it a feature or a bug...
