Hello,
I would like to have more info about canceling the pairing request on iPhone (thru the popup that asks if you want to pair with the device which is managed by iOS...
Hello everyone, I'm severely struggling to perform a simple task. I must be missing a very simple answer and, I hope with your help that I resolve the issue.
I am trying...
if the issue can be worked ,how to do that with android source code? the 2 ble pure devices (not android phone) connect with a ble android phone.
please check below, the...
Softdevice Version： 8.0.0
SDK： 9.0.0 IC：
NRF51822 Rev 3
service： NUS ANCS
When the application is not downloaded, the bootloader is working.
After serial bootloader...
We're looking for a few (2-3) savvy OS X users who might be interested in trying out Xcode to natively develop code for the nRF51/52 BLE SDK's. This build method does NOT...
Hello,
i'm working with my own board with the SD V6.0 and nrf51822 chip id QFAAG0. Already works fine.
Now i switch to the new SD V8.0. The SD V8.0 is programming with...
Hello,
I am working with the DWM3001CDK (nRF52833 + DW3110) using SDK 17.1.0 . I have successfully compiled and flashed the DTM example.
I am trying to use nRF Connect...
Hardware Setup:
Boar d: custom board using nrf5340dk_nrf5340_cpuapp
N CS Version: v3. 0.1 (upgrade d from v2. 4 where it was working)
Problem Description: After...
Hi,
I am wanting to talk to this external 1Mbit RAM chip through an SPI interface: https://www.microchip.com/en-us/product/23lc1024 with the nRF5340 device. Preferably,...
Hi,
I am trying to use the clangd extension with nRF Connect SDK, as it does a much better job than intellisense. I added
set (CMAKE_EXPORT_COMPILE_COMMANDS ON )
...
Hi,
I have autoprovisioned and autoconfigured my nrf52840 board (provisioning and configuring are made inside the software and not through external app/provisioner).
In...
I have read info somewhere which said there is method to crack the protection just by setting UICR APPPROTECT register.
I want to know if Nordic has upgraded the protection...
Hello,
I'm developing my custom sensor application. It's a matter over thread device. Before final product I'm working on a NRF52840 DK PCA 100056 v3.0.1 and NCS 3.02. It...
Hi! We're testing nRF7002 with the nRF7002-DK and NCS v3.0.2. CONFIG_NET_ZPERF=y has been added to the nrf/samples/wifi/shell/prj.conf, the rest is untouched. Running that...
Dear devzone, Can our nRF52840 detect 20 nanosecond voltage fluctuations using COMP? For example, if I set a lower threshold of 20mV and an upper threshold of 60mV, and the...
Hi，everyone:
We are developing a Nearby protocol combined with UWB, which needs to communicate with the Bluetooth of Apple phones and then use UWB to measure distance. We...
Hi nordic： What is the peak current of NRF9151? The relevant parameter cannot be found in the datasheet, while it is available for NRF9160.
Best Regards
JERMI.JIN
Hello,
I am working with the nRF7002 DK board and attempting to use the "Light Bulb Matter" example from Zephyr. I am encountering issues when trying to connect the board...
Hello,
I am trying to build a firmware for the nRF5340 on the Thingy91:x. The firmware should use the external flash for the secondary Image and is using the chained bootload...
I am using the nrf5340 on a nrf7002fk dev kit. I am interested in low power operation so I am measuring the power consumed.
I am running a simple app:
int main(void) ...
SDK 2.3.0
We have a custom board with a few GPIO connected to various interrupt sources (Button, sensor interrupts, power connection etc.)
We are experiencing here sleep...
