I had the same experience as fishman and I went back to give Eclipse a try. (Post: nRF Beacon does not build on Android studio) I tried to build it in Eclipse Luna with the...
When using the BLE device, BLE_GAP_EVT_DISCONNECTED event informs us that connection between dongle and BLE device was closed/lost.
Is there a way to know when dongle connection...
When using nrf51-ble-driver_win_0.3.0 with Visual Studio 2010, after I put a breakpoint in my code, when I try to have the process "continue", I always get unandles exception...
Dear sirs,
Many thanks for the IoT SDK.
Just setting up the Raspberry I can't start the Phyton CoAP example as defined in documentation.
The envirinment is:
R...
Hello everybody,
I'm getting crazy, I'm trying to extend HID axis values from 0..255 to 0..1023 max using the descriptor found in the example ble_HID_keboard/hid_joystick...
Hi, I'm testing the beacon example
(ble_app_beacon, Beacon Transmitter Sample Application ) with my custom board.
I use IAR 7.1 for ARM, Softdevice S110 ver 7.1, and...
Hi,
I'm trying out S130 SoftDevice. I have 1 device with S110v7 which acts as a peripheral.
2nd device contains S130 0.9 (I've based my code on S120 multilink central example...
Hi!
Is there any configuration differences between those 2 modules??
I understand from the data sheets that the pinout is just the same.
I´m testing a PA+LNA on the same...
bnjr, je veut mesurer le rssi entre deux composantes BLE Nano . quels son les fichiers .h qu'ils faut ajouter pour le faire fonctionner ?
merci a l'avance
NB : j'utilise...
I tried to program the beacon kit with the nfr51822_beacon_app.hex through DFU-OTA using the nRF Toolbox on an IPad, and though the upload seemed to work, the application...
How do I configure nRFgo to use the IAR I-jet rather than a segger? When I run nRFgo the nRF51 Programming tab is greyed out and it says no board connected. I presume this...
Hello, I use two nRF24L01+ modules as a transmitter and a receiver, and Atmega8515 as my microprocessors. The transmitter seems to be working as I can see the modulation on...
Hi,
Our manufacturer would like to change the recommended capacitors on the nRF51822 antenna circuit design. Here is the query:
Please check below 3 capacitors request...
I notice in the datasheet for the NRF24L01+ that the receive address needs to be programmed into the Receiver.
Our application receives data from another channel and supplies...
Hi All,
I am looking for a cost effective Chip Socket for nRF51822. The challenge with nRF51822 is that while it is the standard QFN48 package, the pitch is 0.4mm making...
hello,
I have known that Nordic has produced new nRF51 DK which already support s130. But it seems only a demo!
What's the exactly plan of BLE 4.1 and 4.2?
When can buy...
Since windows xp isn't supported any more, I need to get the evaluation kit working with a windows 7 PC. It looks like the problem is with the USB communication. Is there...
Hello,
I am using ESB protocol and there is a definition says "#define NRF_ESB_CONST_MAX_TOTAL_PACKETS 6" so how can I use maximum total packets number? I am looking higher...
How do I configure nRFgo to use the IAR I-jet rather than a segger? When I run nRFgo the nRF51 Programming tab is greyed out and it says no board connected. I presume this...
I am using SD 8.0 SDK 8.0 and MCP 3.8 I am able to find the DFUtarg service and successfully complete the transfer of my applcation (100% complete). However, upon finishing...
Hi,
I'm doing some throughput/current consumption tests with nRF51822 (on PCA10001).
My firmware has been developed starting from hrm example. I have created a custom service...
