Hello,
I recently got a BL653 Click Board and am trying to program it. As I do not have a supported MCU for the NECTO Studio IDE (the ClickBoard's manufacturer IDE), I...
I was looking down at the pinout schematic of the nrf52840 aQFN73, in the schematic provided in the data sheet from v1.1 to v1.11 VSS_PA pin is below ANT pin, but once in...
Hi,
I'm looking to use the nrf connect sdk for development that is compatible with the latest zephyr lts. I believe it will be ncs 2.9.2 compatible with zephyr 3.7.99 (3...
I'm still new to this but particularly in regards to battery. I have a custom board with a nrf5340 and have been working on reading the voltage. I used the battery sample...
This is NOT a runtime error it's a compile time error (application). Failing at stage [154/159] Linking C executable zephyr\zephyr_pre0.elf
Having started by following...
Hello,
I am designing a custom PCBA based on the nRF7002DK PCBA and I really need the Fabrication Notes / Drawing that officially went to the fabricator to direct the build...
Hi,
I purchased nRF52 DK 2 PCs. PCB labeled
PCA10040
3.0.4
2024.34
boath board are new and box packed. from first time itself. I am not able to flash the board...
hi guys,
im developing a program to interface accelerometer MMA8452 with nrf51822.so if accelerometer is in peripheral device,how do i send the x,y,z co-ordinates from peripheral...
Hi everybody, i am working with a nrf51822. S110 with sdk6.1 IDE:keil
I want to do FLASH Erase while in a connection.
I have read this page devzone.nordicsemi.com/......
On initialization of the bsp, I get ERROR 4 (NRF_ERROR_NO_MEM) when I define LOCATION.
Why is this? Because it seems rather weird there's no more memory at that point in...
Hi all,
When I start the bootloader using ble_dfu service as-is in my application I get no ble events in the bootloader. When I call the bootloader from the main loop it...
I have a sample program that is failing on sd_ble_gap_device_name_set with an invalid parameter.
It's calling BLE_GAP_CONN_SEC_MODE_SET_OPEN(&sec_mode)
And then it passes...
Gentlemen: Do you have posted a copy of the original firmware that comes installed on the nRF51822 beacon? I have been experimenting writing my own app on that beacon, and...
Hi all,
I have an TICK interrupt on RTC1 on nRF51822, but the program keeps cycling in the interrupt - as if the interrupt is never cleared?
Here's my code:
void...
Hello,
I am currently building up a little application on top of the ble_multilink_peripheral_example.
I would like to have the nRF Master Control Panel on Android to...
Hello,
First, my setup is as follows:
nRF51822 Rev. 3 dev board (PCA10028)
s110 7.1
SDK 6.1.0
I am developing firmware on the PCA10028. I am matching SPI to a custom...
Well not my best title. But I hope you can follow this explanation:
I added RTT to my project to replace UART. It works so far. But there is a strange behaviour...
Code...
I am trying to do OTA DFU on nRF51-DK from a BLE dongle (CSR 4.0) and gatttool from BlueZ. The image is compiled from blinky_s110_pca10028 example ( blinky_s110_pca10028.hex...
Hi
I want to program the S120 softdevice over an mbed HRM1017 ([link text] that uses nrf51822. I can program only with CMSIS-DAP or drag and drop over the drive. I am using...
Hello.
Initially when reading the Gazell documentation I didn't think it'd be a problem but now in Keil seeing this has introduced some doubt whether it's a thing:
...
