Hi,
i tried to send data from ios 7 via tx_characteristics(like in UART example) but received error:
didWriteValueForCharacteristic 2A38 error = Error Domain=CBErrorDomain...
I have been trying for a few days now to get my environment setup for development with the nRF51822. Since there is no official configuration for the Mac w/ Eclipse I have...
Apologies if this has been asked before but did search for 'format' in faq and got nothing.
I have been answering to questions.
In my answer I place hard empty lines....
Hi
i use nrf51822 s110 "hrs" example to transmit the data to ios.
I need to add an option to send back some data (from ios to nrf51822). 10 bytes maximum .
how can i implement...
Hi
i use the hrs example to transmit the data to ios.
but i need to add an option to send back data (from ios to nrf51822). 10 bytes maximum .
how can i implement...
Hello,when i get connected to the phone,when i call err_code = ble_hts_measurement_send(&m_hts, &simulated_meas) and err_code = ble_bas_battery_level_update(&m_bas, battery_level...
I got the Dynastream N5 kit and have successfully used it with limited ANT work and was trying to get BLE working but can't get a driver for the USB dongle. On the 51422 product...
I can run the SAADC example and read the analog inputs fine, now I've modified the code to simply read the adc with the blocking nrf_drv_saadc_sample_convert call
All I...
Dear All,
while testing an own nRF52832-based PCB and an nRF5840 PDK for current consumption, I compiled and flashed the code below to both devices. Since then I am not...
Hello All,
I don't find any example of Dynamic Multiprotocol of ESB and BLE.
The current multiprotocol example in Nordic’s nRF5 SDK is a switching solution for multiprotocol...
Hello,
Here is a summary of my main transmission protocol:
The (unique) client contact one of the many servers to get the value of a particular server's state.
In the...
hellow nordic.
i use sdk14.2 ,but pstorage_update return NRF_ERROR_NO_MEM.
i use NRF_SDH_SOC_OBSERVER(m_soc_evt_observer, 0, sys_evt_dispatch, NULL) to creat sys_evt_dispatch...
I have a couple of "cannot-be-resolved" issue with Eclipse.
Issue 1:
Sometime when I set up a project in Eclipse, it runs into an issue where types like uint32_t or...
Hi,
I'm trying to send sensor data via BLE to Processing. If someone has already done it, could you post your code or help me explaining how to approach the problem?
I...
Our Nrf51822 will disconnect the connection with timeout reason when it is sending a large amount of data (about 20-70 KB) to our central device which is TI cc2540 . This...
Hi Nordic.
I have questions about preserving device unique information such as device id and so on. (The information will be written in factory)
I know the best way is...
I am trying to add I2C/TWI bus to nrf51822 device. I have used the SDK example code (12.3.0) and keep getting the following errors:
sdk/drivers/nrf_twim.h:69:38: error:...
Hi, Is it possible to make the same nRF52832 device to function as a master for some interval and then switch it to slave?? i.e, Does Nordic have a single SoftDevice capable...
Hello, the current QIAA package is rather demanding on the manufacutring and significantly increases our cost, are there any alternatives? I failed to find any in the datasheet...
Hi !
My goal is to create a large mesh network (over 100 nodes).
I plan to have 3 kind of nodes : a client (connected to a PC), several server relay nodes (not on battery...
Hello,
I have got a question about gpio current protection in nRF52 - I have checked forum but I haven't found answer on this specific question. In nRF52 specification I...
