Hi all,
i want to establish connection between two threads in cmsis-rtos, can i use
1) semaphore to do this?
2)message queue should be used or any other ipcs can be...
Hi,
I have two CPU in our product. (STM32F2 and Nordic nrf51422).
I use serialization function to link those two CPU(refer to ble_s110_serialization sample)
But I find...
Hi,
My behavior is as follows
Turn on my device(use 51422) and advertising(2 Service and 3 Characteristic)
Turn on my cell phone(Samsung Note3),scan my device...
Hello:
I used analog IIC write MPU6050. Again after power download programs, mpu6050 can run up there ACK response. But the debug will not run. Simulation IIC because no...
Hello!
How can I communicate with my nRF24L01+ and nRF51822 at the same time. I can set up same channel, CRC-mode and I don't use ESB. But what about address? How do I set...
Hi all,
i want to know answer related to following question
1)what is use of uicr?
2)if i place some value in uicr and then change the image,then is there will be change...
It used to work, but now it says "Connected" but the rest of the GUI never changes and the mouse just shows a busy spinner. Here's the log file:
0;13:45:18.9900 [MainThread...
Hello,
I was wondering how is calcualted or read on the Thingy firmware the variable w for the quaternion used in the Gyroscope readings.
Looking into m_motion.c in the...
The power data of lfclk is measured under the same hardware and software conditions. When we used two model chips, we found a difference of 1 microamps for the value of the...
hi, I am trying to make buttonless dfu working, but I am not sure how to do that. I am using SDK 14.2.0 with nrf52832. right now, the ble dfu example works. and I found in...
hi
i am using nrf52 dk with MPU 9255 as slave.which pin number of nrf52 dk should i use for 4 wire as SDA, ADO, SCL, NCS.In the attached file ,it is given as p0.20(MOSI...
I'm developing custom PCB with the nRF52832, and I would like to use the ITM for debugging. I don't have a J-trace or equivalent hardware, so everything will have to be done...
I was reading the tutorial :
https://devzone.nordicsemi.com/b/blog/posts/bluetooth-smart-and-the-nordics-softdevices-part-1
it says about how a ble device can advertise...
In Mesh SDK, there are 3 versions available for s132 softdevice: s132_3.1.0, s132_4.0.4, s132_5.0.0.
The question is, should I always use the latest version available? If...
Before I use 51822QFAC(with 32K RAM)， add I must use 51822QFAA(with 16K RAM)。
I have modify IRAM area，like this
IRAM: 0x20001FE8 0x2018.
and selete device is 51822QFAA...
We are designing the nrf52840 with high voltage mode and both DCDC regulators.
Where can I find the requirements for the external circuitry, like the inductors. For now...
Hi,
1. what the DC2DC switching frequency of nRF52832?
2. at nRF52840 the inductor should be 10uH with tolerance +-10% but for nRF52832 this inductor can be with tolerance...
Hey everyone,
I've been trying to get this basic bare-metal application to work. I don't need a softdevice as I'm just trying to turn on an LED. The application compiles...
Could not connect to the nRF52840 preview DK eval kit running the ble_peripheral/ble_app_uart firmware to iOS 11 device running the nRF connect or toolbox apps. We tried on...
Hi:Nordic
Because the nrf52832 can't read 8bit parallel data from GPIOs to RAM with EeayDMA . So I want to use 3 SPI simultaneously to write data to ram with EeayDMA, can...
Hi there,
I have a issue with the nrf51822 UART baudrate setting.
I am developing nrf51822 dongle, its job is to transfer data between PC and a BLE periph. For a stable...
Hi, is it possible for the 824 chip to sleep until woken up by the Bluetooth of a nearby device that wants to connect/pair with it? And what would be the current consumption...
