Hi all,
i want to establish connection between two threads in cmsis-rtos, can i use
1) semaphore to do this?
2)message queue should be used or any other ipcs can be...
Hi,
I have two CPU in our product. (STM32F2 and Nordic nrf51422).
I use serialization function to link those two CPU(refer to ble_s110_serialization sample)
But I find...
Hi,
My behavior is as follows
Turn on my device(use 51422) and advertising(2 Service and 3 Characteristic)
Turn on my cell phone(Samsung Note3),scan my device...
Hello:
I used analog IIC write MPU6050. Again after power download programs, mpu6050 can run up there ACK response. But the debug will not run. Simulation IIC because no...
Hello!
How can I communicate with my nRF24L01+ and nRF51822 at the same time. I can set up same channel, CRC-mode and I don't use ESB. But what about address? How do I set...
Hi all,
i want to know answer related to following question
1)what is use of uicr?
2)if i place some value in uicr and then change the image,then is there will be change...
It used to work, but now it says "Connected" but the rest of the GUI never changes and the mouse just shows a busy spinner. Here's the log file:
0;13:45:18.9900 [MainThread...
Hi,
I am running Keil uVision V5.23.0.0, debugging a 51822 using the J-LINK / J-TRACE interface built into the chips
My code uses SD110, SDK 7.2
I need to get ABSOLUTE...
Hi,
The datasheet for the nRF52840 says that the SWDIO and SWDCLK lines have internal pullup and pulldown resistors already, and thus, does not need external ones.
Two...
I am having trouble tracking down some lingering interrupt source that is waking my application up from the power_manage() command. I am turning off bluetooth advertising...
Hi,
I cannot find the pinout for the P9 connector in the Thingy (programming). My idea was to use the NRF52 DK to program it as this video suggests:
www.youtube.com...
i have flow this tutorial with nrf52840
https://github.com/bjornspockeli/custom_ble_service_example
but d'nt work any body can share an example please ?
Thank y...
In the PCB design reference for the NRF52 we can see that the components L3 and C10 is not parallel with another components and lines. any special reason for that?
Any problem...
Hello,
I have been having issues with two different DK:s. I am doing bootloader development and suddenly the kits go unresponsive.
nrfjprog returns the following error...
Hi everyone. For our product, we need to accomplish tests for CE certification, in accordance with regulations EN300328 paragraph 5.4.10. How can we set the softdevice s310...
I try to integrate the ble peripheral uart example and the beaconing mesh example. It build completed. But when i build and debug on nrf52 board. I have some errors about...
Hello, im a beginner in circuit design, and currently i am developing ESB device that should work on batteries.
Device simply represents a nRF24L01+ module, an ATmega48...
Hi,
I am using nordic nrf52832 nRF5_SDK_14.2.0, I use the RTT for debug, I want MCU in low power mode,so I add the following code:
while(1)
{
NRF_POWER->SYSTEMOFF...
There are parallel 8 bits input to nrf52832 GPIO pins,I want to read the data from the pins and writ it to a RAM.how to do read the data in one CPU clock?
As per this document ....
nrf5_SDK_for_Mesh_v1.0.1_src/doc/introduction/mesh_hw_resources.md
The mesh stack uses flash to store the following states:
- Encryption keys...
