Greetings!
I am using Wireshark along with an nRF52840 dongle to monitor BLE traffic between a mobile app and connected peripheral and periodically I see some "L2CAP Fragment...
Hello, I am using the nRF54L15 board, and trying to connect to the Adafruit SHARP 400x240 monochrome LCD display .
I got the display driver alone to function just fine after...
Hi,
I am trying to perform a DFU using SMP over BLE. My setup has NSIB and MCUBoot enabled and thus I am able to perform DFU for MCUboot and Application using nrf device...
Hi all,
I'm trying to use uart2 on my custom nrf9151 board, but I'm stuck. As I understand, I use i2c1 so I can't use uart1 and i2c1in parallel, so here is why I wnt to...
Hi - I am seeking clarification on a topic as I am a little unsure on the correct way to do things.
I'm using an nRF52840 and porting an old Firmware from nRF5 SDK to NCS...
Hello,
I'm moving my project from SDK1.9.1 to SDK3.0.2. Project is based on peripheral_uart sample (UART part is removed since it is not necessary).
I have encountered...
Hi, i'm using NRF5191 with DECT.
DECT modem: 1.0.2
App: hello_dect sample
In datasheet I found that NRF9151 support various band: 1,2,4,9,22
and I'm using these value...
I want to use the MPU9250 driver found in the Thingy SDK in my nRF52 project. I am using GCC 7.2 Arm/Eclipse as the development environment. The driver source file inv_mpu_dmp_motion_driver...
I would like to implement feature that swaps advertising data only if GAP address in scan request matches one of the application layer ,,authorized'' addresses.
The only...
Hi,
My app was written on Windows PC/MSVC and is ported to nRF52/Keil.
In many places I've used MSVC assert() macro in the following manners:
assert(function(arg1...
Hi all,
On SDK 15.0, Immediate Alert Service is not working without a secured BLE link. When peripheral is not paired, this latter doesn't receive any alert from central...
I’m using SDK 15.0.0. and softdevice 6.0.0.
When I compile the example:
https://github.com/haakonsh/MMD
I get the compiler error:
fatal error: compiler_abstraction...
Hi,
I tried ble_app_uart example by using SES it works fine. Then I tried it by using eclipse with OpenOCD and a STlink V2 on the debug in port I succeeded to flash it....
Hey guys,
With the new SDK15, I find myself looking at dependency problems over and over again. Right now, I am trying to setup a simple A/D conversion using nrfx_adc. Found...
Hi Env: keil uvision 5 and SDK 9 and custome breakoutboard for nRF51822 (PTR5518: no external crystal) and no SD.
I am trying doing the first steps in twi over nRF51822...
I been reading over your entire tutorials, but I have yet to see any tutorials that guides me towards creating an NRF52 project from scratch? Could anyone guide me through...
Hi,
I am transferring my nrf52832 project to nrf52810,and I have deploy the project according to the user guide (Transferring the project to nRF52810 hardware),
when I...
Hello everyone,
I'm developing an application for boards with NRF52832, Softdevice S132 3.00 and SDK 12.3.0.
The network architecture consists of:
one peripheral board...
I'm using my accelerometer's GPIO interrupt to wake up the MPU from PowerOFF mode and it works great. Now, I'm trying to use the same interrupts to wake it up from Sleep mode...
Hi,
I have migrated from SDK14.1 to SDK15.
One thing is embarrassing me.
I would like to modify the scan data as above, I do not know where I can fix it.
phy...
Hi,
I am using mbedos for a NRF42832 and am currently in the situation that I have to profile my code with gprof. Here comes the issue: the Nordic SDK uses explicit assembler...
this picture is from infocenter.nordicsemi.com/index.jsp
and this picture is from 《S132_SDS_v5.0.pdf》
in first picture the application base is 0x00020000 , in...
