Hi,
I am trying to perform a DFU using SMP over BLE. My setup has NSIB and MCUBoot enabled and thus I am able to perform DFU for MCUboot and Application using nrf device...
Hi all,
I'm trying to use uart2 on my custom nrf9151 board, but I'm stuck. As I understand, I use i2c1 so I can't use uart1 and i2c1in parallel, so here is why I wnt to...
Hi - I am seeking clarification on a topic as I am a little unsure on the correct way to do things.
I'm using an nRF52840 and porting an old Firmware from nRF5 SDK to NCS...
Hello,
I'm moving my project from SDK1.9.1 to SDK3.0.2. Project is based on peripheral_uart sample (UART part is removed since it is not necessary).
I have encountered...
Hi, i'm using NRF5191 with DECT.
DECT modem: 1.0.2
App: hello_dect sample
In datasheet I found that NRF9151 support various band: 1,2,4,9,22
and I'm using these value...
Hi there,
on the nRF5340 Audio DK, there is a FT2232H, which provides FTDI_SPI + FTDI_SPI_SEL.
How this can be used, is there any sample for this available?
And how...
Hi
I have some questions about nRF5340 & nPM1300 decoupling cap
nRF5340
1.For pin A3/D2/H11/K1/L5/L11, ref. SCH is 1uF*1 and 0.1uF*5, could we only connect 1uF*1 and...
Hi guys what's the latest revision of "nRF51822 Bluetooth Smart Beacon Kits"? that's the beacon with the battery, the revision is written on the envelope.
I thought it...
Hello everyone,
The more I learn, the more I learn how much more I have to learn.
I am pretty new to embedded systems development. I am tasked with developing an nRF52...
Hello,
I've had to redesign my bootloader and I am now stuck with a problem that I can not solve. I need to know the correct workflow for switching from bootloader to application...
I use the nrf51822QFAA, and s110 v8.0.0.
now I need update the application,i have the keil created hex file,
How can I create the ZIP file use the application hex file?...
I have built a PCB that includes the nRF51822. I have AIN7 reading an input voltage that I measure on my DMM at 269mV.
When I measure the voltage through the nRF51822's...
Hi, I have an application where I am recording button presses using a beacon-like implementation. The button presses represent start/finish events for a race and are communicated...
In my setup, i have a Node with SD130 as peripheral to Smartphone and as a central to a BLE peripheral.
I need to store some Unique ID about the Smart phone and a Peripheral...
I find out that
The s110 can only connect to a single
central, but is able to do
non-connectable advertising while in
that connection
by here
So is this...
Hello,
I have a problem with the sd_flash_write function. It HardFaults on me and I can't seem to find out why. The Addresses are 4 byte aligned...
The function is called...
Hello,
I have written a timer driver with timer 0 without SD and used 24 bit mode and it is working.
But when I used the same driver with softdevice and Timer 2 and...
I have a problem enabling TIMER1:
If the prescaler is set between 16MHz and 2 MHz the firmware fails to enable the SoftDevice, even if I didn't manage TIMER0, but TIMER1...
Hello, I have looked into the compatibility matrix and I couldn't find any clear answer about if the NRF Beacon Kit is compatible or not with the S130.
Does anyone tried...
Hi,
I'm now going to combine the proximity program with the ancs program, but I don't know how to make it.
When I try to add the proximity program to the ancs (I add tps...
