Hello,
I am designing a custom PCBA based on the nRF7002DK PCBA and I really need the Fabrication Notes / Drawing that officially went to the fabricator to direct the build...
Hey everyone,
Does anyone here have experience with firmware OTA updates over the JIO NB-IoT network? The process seems a bit different since JIO Cloud always sits between...
Hello:
The latest nRF54L15 Errata for Rev 2 shows that the previously reported "GPIOs can exhibit radiated emissions" is no longer present in the Rev 2 SoC.
Can you please...
Greetings!
I am using Wireshark along with an nRF52840 dongle to monitor BLE traffic between a mobile app and connected peripheral and periodically I see some "L2CAP Fragment...
Hello, I am using the nRF54L15 board, and trying to connect to the Adafruit SHARP 400x240 monochrome LCD display .
I got the display driver alone to function just fine after...
Hi,
I am trying to perform a DFU using SMP over BLE. My setup has NSIB and MCUBoot enabled and thus I am able to perform DFU for MCUboot and Application using nrf device...
Hi,
I would like to test a websocket connection over NB-IOT with the nRF9151DK. I started with the websocket_client example but I have those warnings and errors at startup...
I'm getting the following notice/warning/error when building my application (nrfsdk 2.9.0 w/ sysbuild, nrf9151dk board):
/usr/local/zephyr-sdk-0.17.0/arm-zephyr-eabi/bin...
Using nrfutil/dfu, I have previously flashed an older application+SD (s132_nrf52_3.0.0) onto the nRF52840 dongle.
Now, I cannot flash my newer application, since it contains...
Hi All,
Simply put I am trying to use the Xiao BLE Sense board connected to the Expansion board (with SD card slot) to write audio recorded data from the Xiao embedded PDM...
Hello, I'm programing my project while using the nrf52840 chip. I'm using segger embedded studio for the programming part because with the nrfconnect I have error code 9 ...
Hi I wish to integrate Matter over thread in unicast audio server . My objective is to use matter to control the volume and play/mute states. I would like to know whether...
Hello, checking if it's at all possible to have uart working on the nrf52832-dk using pins 18 and 21. I can get rx/tx working with an ftdi using pin 12 & 13, but not 18 &...
SETUP:
2 x NRF54L15 DK initiator/reflector sample (as of 4/8/2025) Major RTT settings below - RTT (BT_CONN_LE_CS_MAIN_MODE_1) with 1M phy, 32 bit random RTT (will add settings...
I am working with nrf52840 dongle, details on the antistatic cover are( nrf6829, 2.1.1, 2024.02). I am trying to flash it using https://github.com/adafruit/Adafruit_nRF52_Bootloader...
Hi all,
I'm facing a challenge with efficiently transmitting high-frequency sensor data over BLE.
I’m sampling sensor data via SPI from a sensor capable of outputting...
Dear Team,
I am attempting to provision my Thingy91 device to AWS IoT Core using Fleet Provisioning with the Claim method. I've been closely following the instructions in...
Hi everyone,
I'm experiencing an issue with my nRF54L15DK board.
When I build the OpenThread CLI sample with the /ns configuration, everything works as expected. However...
Hello, I am working with a Seeed XIAO nRF52840.
I'm able to get an average of 500 uA in SYSTEM OFF mode. However, for this application, the current consumption during wake...
Hi guys, With v2.8.0 sdk, L4_e3 code ( academy.nordicsemi.com/.../) works with nrf52833dk. We have a custom board that we designed. Here, nrf52820 chip is used. I can compile...
Hi,
I have thingy:53 and I have damage to the sw2 pin and I am unable to enter the DFU. I lost two tiny pieces that go just above the one in the photo and not even...
