Hi
We are developing software for the nRF51 with Keil under VirtualBox. Previously we used the PCA10000 dongle with the Master Emulator and MCP without issue. Now, with...
We are using nRF51822 for our products.
We want to know the min value of "Receiver sensitivity" when we use this chip for BLE.
The Datasheet says "Receiver sensitivity...
Dear
The BLE Multi-link example (ble_app_multilink_central and ble_app_multilink_peripheral)
shows how one central device can connect to multiple peripheral devices. ...
In the MCP app, if I have the following service data for an Eddystone beacon:
0x10, // Eddystone-URL type
0x00, // TX power in dBm. This is a signed integer so 0xEE ...
I have the nRF Control Panel Android application. It works fine with several BLE devices, but specifically for the Fitbit Flex, it fails to connect.
I know Fitbit wristbandes...
Hi,
The situation:
I was able to successfully receive known packets from a device running gzp_device_dynamic_pairing, from, the host running the gzp_host_dynamic_pairing...
Hi everyone
nrf51822,softdevice s130 2.0.0
now i used softdevice s130 establish two connection as a central with two s110 peripheral device,at the same time i establish...
Sorry I must have missed some crucial bit of documentation.
I have some code working using GPIOTE, however the inputs of the hardware, that will connected cannot be driven...
Hello,
I have interfaced MPU accelerometer on i2c and GPS on UART. Have enabled UART and using printf to display both sensor data. To begin with, both work fine individually...
Hi,
I checked erratas for nRF52840 rev1 and #164 is gone but #191 is still there. Can I have both #164 and #191 active in my code and it won't cause problems on either engineering...
Hello,
I have a question regarding the nrf uart driver. The RXTO event is never triggered even though the Interrupt itself is enabled (and the line is idle after a packet...
hi,
In Light switch Example ahead of time he have 3 Servers so we set SERVER_COUNT=3
if I want to develop Mesh Network..Where I introduce new Node, Provision the node...
when i use other hex file, it appear every time.
after i click "yes"， i can't scan the divece?
so what the proble ? how can i use "nRF Connect " with other hex file ,...
Hi everyone.
I want to use the nRF8001 in a low power application and therefore I want to save as much energy as possible.
I read in other discussions that the nRFgo studio...
Hello,
We are mocking our code but we are having difficulties eliminating the dependency of other files the mocked file includes due to the mocked header including the...
Good morning,
I am running the UART example from SDK 14.2 (example/ble_peripheral/ble_app_uart) on a brand-new NRF52832 development kit (PCA10040).
On the master side...
Hello.
I try to periodically updated data in my characteristic that way:
As soon as I connected via "nRF Connect", function " sd_ble_gatts_hvx" returns: NRF_ERROR_SVC_HANDLER_MISSING...
Hi all ,
I have SHT31 and I can read Temperature and Humidity value by NRF52 . But I want to create 1 service for display it on smart phone with the RH (name: Humidity,...
Hello,
I would like to measure the voltage of circuit GND by using the embeded SAADC of nRF52832.
But unfortunately I have no vacancy of GPIO to connect GND.
Could you...
I have set up a nrf52840 kit to upload data to nrf cloud via bluetooth but the data on the cloud is displayed as a hexadecimal number(1,2,3,4,5,6,7,8,9,A,B......) I want to...
I am not seeing a transition to BLE_ADV_EVT_SLOW. The transition I see goes from FAST to idle, without a transition to slow, from the configuration I don't expect to be in...
