I'm still on stack 8.0.0 so it might have been fixed since. I have noticed that if the other side de-asserts CTS the Nordic code will leave the TX asserted in a Break condition...
Hello,
I'd like to ask what is the data rate when using BLE OpenMesh network and how much it depends on network architecture.
I'm considering using it in a network consisting...
Hello Nordic Community,
I need to know how to import my PCB design from Eagle to CST Studio to simulate it and I need to know if the simulation step will be useful to enhance...
Hi.
I'm trying to get Apple notifications to nrf52. And specifically to listen both regular ANS (for android) and ANCS (for iOS) events depending what sort of phone is...
I am trying to find out the part number of the antenna (I assume it is a PCB antenna) used in the nRF51 DK ( www.nordicsemi.com/.../nRF51-DK) . I found a lot of similar questions...
Hi.
I am using the NRF52 Development board, on Keil uVision, to implement a C program that uses Dynamic Structs. The Structs re-size themselves ( by increasing their capacity...
Hello,
I have an NRF51822 (redbealab ble nano) that I would like to use to count pulses in very low power mode.
Pulses are asynchronous
The rate of pulses can...
Hi,
I 'm using MCP v3.9.0.6, softdevice v7.2.0 and pca10003 board.
After load bootloader program to board. I use MCP to load application for it. In MCP, I choose device...
HI People,
I use nrf51822 CEAAE00 (0x0079) chip which has 256 kB FLASH, 16kB RAM. I faced a problem when compiling the bootloader for it. The solution was I am using a...
I am trying to build a custom board, based loosely on the nrf51-DK (which I have been testing). I haven't ever directly programmed a chip before (always used interface MCUs...
if I send only the advertisement, it sees that data
Is there something in the IOS that prevents seeing manufacturers data in both the advertisement and response packet?
I found the Ble Serialization here and the example sourcecode within the sdk sources.
The sources are for using S110 softdevice.
Does Ble Serialization also working...
Hi, I'm trying to get my nRF51 code (which works on my dev machine) to tun on the test server (both Win7). Am using MasterEmulator 2.1.10.8567
The dongle itself is happy...
Hello I am new to this platform, can anybody tell me how to write the value on serial in NRF51822
and what is the command through which i can write the value on serial. getch...
My application uses ble_radio_notification_init. Every time I switch from my application to the DFU bootloader it drops the connection about 10 seconds after starting the...
Trying to follow
devzone.nordicsemi.com/.../
but whatever I do, I am unable to make Eclipse discover the include paths or the source file paths from the makefile. I've...
Hi,
My Nordic kit just stopped detecting from last two days.
I have also check this in other PC also.
It detects some times some times not.
I am using Windows 8.
I...
Hi all,
I would like to know if it is possible to use the uart before the actual bootloader runs... I need to communicate with the master uploading the firmware before...
Hi All,
I need to implement a kinda a mesh network of Nordic device nodes placed nearby to act as a relay, for that I have a use case where following requirement.
...
I'm porting a nrf51 project to nrf52. I'm using softdevice s132 1.0.0.3 alpha. When compiling I get a lot of L6406E errors and a L6407E error. Do you know what's causing this...
hi,
I should how to transplant the official DMP mpu6050 library to nrf51822 above?I don't know how to transplant it and could you tell me how to transplant it?
