Hi,
I'm running Mac OS X 10.10.2 with the nRF51-DK PCA10028 card that I received today. I started off following the instructions in this article , and was able to get JLinkExe...
Hello,
I would like to do an communication between Arduino and Android platform.
In my case, Android will be master.
But I want also test between 2 Arduino with an Bluetooth...
Hello,
I would like to develop a custom key sharing algorithm for nRF8001 chips. As far as I have understood the only way to use full 128-bit temporary key (TK) is OOB...
i am useing nRF51822 pairing with nRF24lu1 over GZLL protocol now,
is there someone have the experience on how to config the parameter of GZP_TX_RX_TRANS_DELAY in function...
I have a peripheral running the S110 stack, which presents a characteristic to which I want the central (running S120) to be able to do a long write. What I've been trying...
Hi all,
I have been trying to combine the UART and hID Keyboard examples into a single application.
I want to use the HID part to send specific keystrokes using buttons...
Hi,
I have a project with 52810 which I use rc for LF clock source and I need use P00 and P01 as general GPIO, I have set both CLOCK_CONFIG_XTAL_FREQ and NRF_SDH_CLOCK_LF_SRC...
We are developing an nRF52832-based circuit with 1.8v power supply, which features BLE, NFC, SAADC, I2C & SPI.
According to datasheets, all 3rd party components are also...
Hi,
we plan to use the nRF52832 for a new project, I have two questions:
LE secure is supported, is this right ?
We want to pair up to 8 phones with our device....
Hi,
I am using SDK 14.2 with nrf52840 board. In my project I am using USB and BLE together. I have noticed that when I enable the LE Secure pairing and after that my USB...
Which nrfutil version should be used with Mesh SDK?
Getting started for Mesh has the link to nfrutil verison 0.3.0.0. In pc-nrfutil github repo the latest version is 3.5...
Hi!
I try to do simple led blink on nrf51822 and after build i got this:
Checking project status
Building ‘dongle’ from solution ‘dongle’ in configuration ‘Debug’
Compiling...
Hi,
I am using Segger IDE and now I wanna to use the temperature sensor presents in the PCA10040 board.
I tested the SDK example using the keil and works fine. When I...
I have your NRF52 DK and beacons.
I want to make the case so that my Nordic NRF52 DK will get data from Nordic beacons and forwarded that data on the UART port of PC....
Hi there,
I am developing a BLE dongle, and a BLE peripheral both based on NRF51822QFAC. The BLE dongle scans, connects, and disconnects the BLE peripheral by UART commands...
Hi
I get the following compiler (assembler) error in my project:
... Compiling file: hardfault_handler_gcc.c /tmp/ccstUNqW.s: Assembler messages: /tmp/ccstUNqW.s:46: Error...
Hey All,
I'm using the nrf_drv_uart UARTE driver (NRF52832) communicating with an external device. The UART init code is executed using a function (call all_main in this...
Hello All,
I am working on NFC using nRF52832 chipset .
I followed the below this link for http://infocenter.nordicsemi.com/index.jsp?topic=%2Fcom.nordic.infocenter.sdk5...
Hi everyone :D
I'm not being able to compile a c++ code on segger embedded studio.
The same code compiles with the Makefile provided in the SDK 14.2, but not with the...
Hey, we are using the nrf52840, and the SDK 14.0.2 and the uart example. We need to set the BLE range to max, and therefor the TX to 8db, the transfer speed to 125kb/s. We...
