Dear Technical Support Team,
I am trying to integrate and run TensorFlow Lite Micro on the nRF5340 Development Kit using the nRF Connect SDK. I have tested both SDK version...
Hi,
I am working with the NRF52832 SoC using the NRF52 DK and developing with NRF Connect SDK version 2.7.0. I have enabled BLE with LBS, BAS, and FUOTA services, along...
Hi,
Is it possible to advertise legacy (without extended mode) and coded simultaneously, and both connectable?
I see the sample from nRF Connect SDK, multiple_adv_sets...
Hi,
I am trying to port the DTM example to our board, 52833 based but when DTM is initialised I get about 1400ms of CW then:
00> *** Booting nRF Connect SDK v2.5.2 **...
Hi Nordic team,
We are planning to use the STM32H747 as the host MCU to control the nRF7002 for Wi-Fi functionality. Based on reference materials and existing use cases...
Hello Nordic team,
I am working with the nRF54H20 and would like to integrate both Enhanced ShockBurst (ESB PTX) and Bluetooth Low Energy (BLE peripheral) protocols in my...
Hello, I'm testing the nRF21540 FEM on a custom nRF52840-based board using the nRF Connect SDK.
I’ve enabled CONFIG_MPSL_FEM CONFIG_MPSL_FEM_NRF21540_GPIO_SPI CONFIG_BT_LL_SOFTDEVICE...
We are a contract manufacturer. We are trying to help one of our customer's with their bare board design which uses your NRF24L01+ (NRF24L01P) that comes in a 20-pin 4x4mm...
Hi!
We are currently writing a simple bootloader which reads the new application image from a external SPI based flash memory. We are using the S110 SoftDevice, which works...
Hi All,
I have been developing a bluetooth chip based on nRF51822 QFAC. I have followed the design rules very closely but at the end I do not get any bluetooth signal coming...
main.c Hi ,
I'm using nRF51822 and S110 stack and sd_6.0.0.
having an ble app UART example.
Facing a strange problem that when (from nrf Uart App)connecting and disconnecting...
Hi
I set one GPIO interrupt with low-to-high sense, but seems it did not triggle the interrupt when SD run.
I want to confirm the SD would make the interrupt loss? If so...
Hi folks,
I have a 2MHz clock (call it DRDY) coming into my nRF51 on one of the GPIO pins (call it AFE_DRDY). I need to read an external AFE chip on every falling edge...
I have a project where specification requires disconnecting immediately after sending a response to a BLE read request. I'm using authorized reads.
Currently, I'm using...
Hello,
I am measuring 5~6 mA of current consumption in standby mode, even when not broadcasting/connected. Why is it so high?
Aditional info:
I am using a custom...
I am using IAR workbench. Using softdevice s110 Version 7.
I have created a bootloader at memory address 0x3A000.
My application sits at 0x16000.
My application checks...
I used the sample code from nordic with nRF51822. DTM works fine. sensibility test gives me 0% on the 3 channels. Perfect.
Then I copied and paste into my code, calling...
I'm compiling and running correctly but the Keil software program for St- Link does not work I have . Have a different method to compile and install nrf51822 ?
on iOS 9 beta 5, ANCS doesn't work.
Steps to reproduce:
On iPhone, Settings -> Bluetooth
Tap to connect and pair
Make a phone call on another device
no caller...
Good work,
I am trying to control with android i nrf51822 But I have a problem. Ten LEDs After connecting the device with Android when I press the off button or "device does...