We are considering using Gazell for an outdoor application, i.e. lots of noise and disturbances, constantly changing environment, where the amount data being transferred is...
Hi everyone,
I have found your git "Ble Optiboot"( github.com/.../ble-optiboot) , and I have understood, it is usefull to load a binary into MCU flash, I was looking for...
I'll go ahead and describe what I need to do and see if anyone might have some place to start for me since I'm having a lot of trouble figuring out what I need.
I'm looking...
Hello ,
I'm designing an embedded system with one of your RF chips (NRF24L01+) and as far as I searched for the datasheet , It seems like NRF24L01+ doesn't have a hardware...
Hi,
This post is very old.
devzone.nordicsemi.com/.../
I have a nrf51822 chip and I'm using it as BLE and it exposes some service and characteristics and it is working...
Hello!
I set up a project using NRF24L01 and a patch antenna ceramic, the type used in GPS.
In fact, I tested several types of antennas, F, F inverted, GPS, Loop. But...
Hello,
I'm trying to create a PC application to read out some Ti Sensor Tag modules. I'm using a nRF51822 USB dongle and the Master Emulator api.
The nRF dongle sees...
I measured the current drawn by the nRF51822 beacon with its default beacon code. The current was about 1 mA which was same as in another thread
The suggested solution...
We have been manufacturing for a while with the nRF51822, Revision 2, and WLCSP package and build code D0 (D0 is what Nordic recommended me to spec to contract manufacturers...
Hi all,
I have application that read analog level and send the data with connection interval of 10 ms and 0 dBm, how can i calculate the current consumption of BLE? i read...
Hi
I want to use Printf() in the DT2 but it cannot output msg to terminal.
I used hal_uart_config() to config UART TX/RX/Baudrate... in mail.c then
call hal_uart_put_str...
I use S110 V7.1.0,nrf51822 chip,
now I need write and read flash data in BLE mode.
When can I write the flash data at BLE mode?
When can I read the flash data at BLE...
I'm calling the requestData function and lib_aci_close_remote_pipe at the same time.
The lib_aci_close_remote_pipe returns 0x8E command error which means: "Command rejected...
Hello,
I need to store some app configuration on the FLASH and I'd like to use the features of pstorage module.
I don't understand the following thing ...
When the...
Hello,
I am currently using the SDK setup from this URL: embeddedsoftdev.blogspot.de/.../ehal-nrf51.html
In order to use that setup, one must change a line in the file...
Hello,
I downloaded MDK arm from Keil website (keil mvision 5), SDK and MDK pack from nordic download site. After installing SDK, I am not able to find example projects...
Hello,
I have quite a few of setting on my nodes and I want to save some of these permanently. Currently I am using the pstorage module and everything works as expected...
Hello everyone,
i can able to set the static passkey but i would like to know the difference bewteen security key and passkey how can i set security key ? any suggestions...
Good day!
Faced with the problem that I didn't get to run N5 Starter Kit (nRF51422) on maximum speed in Advanced Burst Mode, using ANTware II with ANTUSB-m to read packets...
I read the multi-role project on Github. For time slot part, there's no explicit hfclk start/stop operation along with the radio events, is it possible that sd_radio_session_open...
In the nRF8001 Arduino SDK, there is a " ble_bandwidth_test " example.
It says,
"The bandwidth is measured (sic?) with the nRF UART App in the Apple iOS app store" ...
