Hello,
I would like to develop a custom key sharing algorithm for nRF8001 chips. As far as I have understood the only way to use full 128-bit temporary key (TK) is OOB...
i am useing nRF51822 pairing with nRF24lu1 over GZLL protocol now,
is there someone have the experience on how to config the parameter of GZP_TX_RX_TRANS_DELAY in function...
I have a peripheral running the S110 stack, which presents a characteristic to which I want the central (running S120) to be able to do a long write. What I've been trying...
Hi all,
I have been trying to combine the UART and hID Keyboard examples into a single application.
I want to use the HID part to send specific keystrokes using buttons...
Hi, I'm new to BLE and just started feasibility testing, using RF8001, on a small device with no IO. The device will have a unique code set at factory, and printed on label...
I had the same experience as fishman and I went back to give Eclipse a try. (Post: nRF Beacon does not build on Android studio) I tried to build it in Eclipse Luna with the...
When using the BLE device, BLE_GAP_EVT_DISCONNECTED event informs us that connection between dongle and BLE device was closed/lost.
Is there a way to know when dongle connection...
Hello
I am working on a proprietary radio protocol while dealing with a problem that I stuck at for 2 days now. I am managing to get the radio stuck in a TX state (NRF_RADIO...
Hi,
I would like to ask a question about the power consumption specified in nRF8001 datasheet:
the graph on page 40 shows that the average current consumption is about ...
uart not accepting my static passkey when i added dfu in my project. using ios app nrftoolbox.
programed soft device s110. programed dfu dual bank example project then uploaded...
hi i am trying to setup a connection with CP2130 with nrf51. i am using nrf6310 kit. i flashed the spi slave example into into nrf51. on nrf51 these are the connection pins...
I am attempting to wake up every 250ms using an app timer to manage some background tasks and update our BLE advertising manufacturer data if needed. However, once we enter...
this the origin code of offical,,,this some err?? help !!!!
static int8_t channel_port_alloc(uint32_t pin,nrf_drv_gpiote_evt_handler_t handler, bool channel)
{
int8_t...
Hello,
I am using nrf51822 and I want to get RSSI values as much quick as possible(around 20 samples per second) .
Previousely I used MCP and decreased the scan interval...
Hello,
i'm working with my own board with the SD V6.0 and nrf51822 chip id QFAAG0. Already works fine.
Now i switch to the new SD V8.0. The SD V8.0 is programming with...
Hi all
We use the nRF51822 with the S130 V1.0.0. Our application initializes the TIMER2 (f = 16MHz) with a EVENTS_COMPARE interrupt on the CC channel 1 to monitor some...
I have an implementation of pstorage that works very effectively in one build of software, but is dramatically slower in another. Specifically it is taking 10 minutes to actually...
Hello everyone,
i just stuck with bluetooth Range in nrf51822. I am transmitting data using bluetooth at +4dBm(which is maximum). In my experiment my nrf51 dongle is moving...
Hello, I am using the examples\ble_central\ble_app_hrs_c project from SDK_8.1.0 with s120_nrf_2.0.0 on an nRF51422_CEAAB00. This when the variable m_scan_mode set to BLE_FAST_SCAN...
Hello Noric expert.
I am stuck with writing data to flash. I am using nordic's nRF51-DK.
My sdk version is 9.0
Could you go over my code ? My code is attached.
...
