Background
Our device uses the CONFIG_LTE_NETWORK_TIMEOUT option from LTE Link Control, which by default is set to 600 seconds (10 minutes). I haven’t found any specific...
Hello, as the title suggests, I have an issue when powering the nRF9151 DK with an external power supply. Normally, I power through USB, and it's fine. However, when I followed...
Hi all,
I am using and nrf9160, in particular a thingy91. It is running 1.3.7 firmware. I have the SLM sample loaded and can sent AT commands to the device using the nRF...
Hello,
We are working on Zephyr sample app Mesh on nRF52840dongle with nRF Mesh application.
After going through the documentation and few other Q&A on the portal, I was...
Hlo
I have to asked that i am working with custom board of nrf5340 and i want to flash and check the rf signal by flashing through the nrf5340 development board and i am...
Hi all,
I'm encountering an issue with the TWIM30 interface on the nRF54L15 (pins P0.03 - SDA, and P0.04 - SCL), using vanilla Zephyr v4.2.0-rc1.
The setup involves external...
Hi,
I purchased a Qorvo QM33120WDK1 UWB development kit that uses a Nordic nrf52840-DK. I have been using this DK for weeks without issues, but the last time I used it...
Is there a simple software code example how to configure an interrupt handler for a single GPIO-pin? I am using nRF51822 chip with softdevice S110 and the interrupt source...
My question a little weird. Because I am super beginner about BLE. So what I want is how to write string data. now i am looking to information about this. I cannot find it...
Hi
I'm trying to implement bonding in a device based on the S120. As counter part i've used a S110 device or an iOS device (realized with LightBlue App).
While searching...
Hi All,
I am using nRF51422 and now doing ANT+ certification test with tool v1.3.6. And i find out some problem with the received value on my display in case of following...
Hi
i am not able write my application after I flashed the SD. I am using Jlinker lite (the one that comes with the Dev kit) and the scripts from the nrf pure gcc . I modified...
Hi everyone,
Is it possible to connect 2 devices simultaneously with the nRF51822 device? As soon i connect one device, the advertisement stops.
So, for me it would be...
I've already posted my problem here. But it seems a dead thread.
devzone.nordicsemi.com/.../nrf51822-timer-problems
I ran into trouble when using the app_scheduler without...
Hi, I've been trying to use the timers on nRF51822 but I just can't get them to work in my code. When debugging (with GDB and Eclipse), the execution always stops with the...
Hello.
I've asked a question a while ago, devzone.nordicsemi.com/.../sd_flash_page_erase-failing-with-s120
I've been using Linux, jlinkexe, and gcc that time. Now I...
I just got the new Nordic "mbed" dev board and have started experimenting with it.
In another thread it is explained that the softdevice is bundled into the generated ...
I am getting following error:
Error in final launch sequence
Error executing step execute method: stepInitializeJTAGFinalLaunchSequence
java.lang.reflect.InvocationTargetException...
Hi Dev Team,
Please guide me that, What is the data format needs to follow between BLE profile and iPad in order to transfer data.
I am performing both update(read) and...
Hi,
We have an extra current of 1uA while in system off mode(no RAMS). we get ~1.6uA instead of 0.6uA as we read on SPEC.
Do you have an idea what may cause the extra 1uA...
I am trying to modify the ble_app_hrs so that i can write a value to the board and save it as a new heart rate value. So far i have added a BLE_GATTS_EVT_WRITE case to the...
