Hi,
To use bidirectional continuous scanning mode in ANT, I have to transmit Extended Broadcast/Acknowledged/Burst messages using ANT Msgs 0x5D, 0x5E, and 0x5F (ANT Message...
We are preparing to get BT qualification for our product, developed with the 6 stack now, however want to update to 7 when it is finally released. A comment from the testing...
What is the best way to minimize transfer in progress errors when trying to send ANT messages? I am using the S310 stack on an nRF51422. I have a busy ANT channel that is...
I'm running into a weird timing issue with a nRF24L01+ which I'm not quite sure how to work around in the general case. The basic setup is two radios, A and B. Auto acknowledgement...
I am using mbed library to get leg up on development.
This is the first time I am writing any MCU application and it sure makes things a lot easier.
I am using nRF51822...
I've recently began experimenting with the HID service and connecting to iOS devices in order to achieve lower connection intervals with Apple products (as described in their...
The link from https://docs.nordicsemi.com/ to the latest nRF SDK documentation is broken.
https://docs.nordicsemi.com/bundle/ncs-latest/page/nrf/index.html is not wor...
Hi Nordic team, I'm currently facing a bit of a snag while trying to establish communication between the nRF52840 (NCS 2.5.0) and the MS5540C sensor using a 3-wire SPI protocol...
Hi Nordic Team,
We are using the MIMXRT1050-EVK as the host and the nRF7002EK as the Wi-Fi module with an SPI connection. However, we are encountering frequent errors that...
Hi,
I am working on a sensor device that requires very accurate timing on the sensing and sensor signal algorithm side. This device needs a low latency and low jitter radio...
Hello,
I'm looking to get XInput working on the nRF52840 so that our device can appear as an Xbox-compatible game controller. I'd appreciate any guidance or recommendations...
I want to add custom outputs to my custom board dts: this thread mirrors exactly what I'm doing:
https://devzone.nordicsemi.com/f/nordic-q-a/92813/how-to-declare-a-single...
Currently advertising packet is built by macros, but the data types include const qualifiers.
What is the "proper" way to dynamically update advertising please? I need to...
Hi, I'm using the nRF52840 to measure voltages through the SAADC . I'm observing a measurement noise of around 80mV peak-to-peak on inputs AIN0, AIN4, and AIN5 .
Here are...
Hi,
In our devices, we use an NRF51422 chip.
In our software we use the S210 v3.0 version of the ANT softdevice. I am trying to find the anomaly list of this ANT softdevice...
Hi,
We developed a custom board based on the nRF54L15 SoC. We realized many current consumption tests with regulator configured in DC/DC mode. These measurements are in...
Hello everyone,
I'm currently developing a project that involves combining LoRa and maybe NB-IoT technologies. For this purpose, I've already been utilizing an nRF52840...
Hi, I'm using nRF Connect SDK (v2.1.2) with VS Code on Windows for a project targeting nRF52811 .
Even though everything is versioned in Git, I keep running into the following...
As subject, the key is using prj.conf, compilation errors will occur, if do not use prj.conf, c ompilation pass but 54L15 not work(no logs aft pwer on). Is fast pair(locator...
Hi,
I have an issue with VS code. The connected devices does not show my jlink debugger nor the DK. However, nrf connect desktop programmer shows them.
Toolchain: v2.6...
Hello, just like the title indicated, I need help with setting up the nRF21540 EK with the nRF9160 DK.
For my application, since the nRF9160 DK has the nRF52840 on it, I...
