Hi Nordic Teams :
I would like to check the current consumption by BLE DTM.
1. Is the table measurement is from 3.0V input?
2. I find the condition in the datasheet...
Hi am trying to use Nrf54l15 as a controller with an external host for the Channel sounding feature. I can receive CS subevents from the NRF controller, but the same thing...
HI ALL,
nrf54l15dk,v2.8.0,peripheral_uart demo and no changes have been made.
Then add the following content to prj.conf
sysbuild.conf
mcuboot.conf
At this...
Hi,
I am programming with ncs v2.9.0, nrf52833 chips.
I am going to get pc keyboard led state in my custom board throutgh BLE.
This is my report map,but cannot get data...
I'm developing my application with nrf 52832 and nrf SDK v17.
I know NCS is more powerful. I'm currently learning how to use it.
But now.I still need my application with...
I'm writing a wav file from the nrf52840 board to the nor flash w25q128jv with a capacity of 16mb but it seems that I can only operate on the first 2mb, even when dividing...
Hi Sir,
As check below link, the battery profile can support on non-Nordic MCU.
(+) Does the PMIC nPM1300 support Fuel Gauge feature for MCUs outside the nRF SoC family...
Hello Nordic forum,
I must not quite understand how CoAP callbacks should work. Would anyone be able to give me any advice as to why my modified coap_client results in undefined...
Hi,
Im currently trying to add FOTA via BLE to my project.
To get familiar with this i wanted to add FOTA as described in the nrf connect intermediate course lesson...
I tried to find an explicit statement whether a new IMEI needs to be written to nRF9151.
These sources state that nRF91x1 ships without IMEI and it needs to be written:...
Hello, I have a project based on nRF9160 and nRFCloud (CoAP), and uses a SIM from 1NCE. This SIM allows to connect to 3 different MNO at my location in France (Orange, Bouygues...
Hi I want to know if I can use the nRF52850-DK to flash the Xiao Sense Plus from seeed? I am following the following tutorial which says I need to use a J-Link but that's...
I am new to Zephyr RTOS . i have a breakout board of Max32664D from protocentral interfaced to nrf52840 development kit . i want to get started with this sensor hub max32664...
What is the default transmit power of the nrf5340 when performing an AoA test in connected mode? How do I change its transmit power to perform AoA accuracy tests at different...
Hi,
I tried to change security level, but it's not changing.
When i set CONFIG_BT_SMP_SC_ONLY =y, it's working well with security level 4,
but i want to change mode1...
Hello everyone,
I am a beginner looking to dive into the world of HID (Human Interface Device) development, specifically using the NRF52840 microcontroller. I recently...
One of our products that's been in the market for a couple years is a bit behind on the NCS version (v1.4.2). I am currently doing the 18031 RED Cybersecurity documentation...
Hello,
I am a beginner when working with nRF. I am trying to run the l4_e3 solution code, but it doesn't seem to work. I can connect via BLE, but nothing is being shown...
i want to advertise my one device into coded and into another device i want to do coded distance measurement it is possible to do in nrf 52840 version 2.5.1 ?
Helo, I have ISP1907 for BLE AoA.
In my understanding, the antenna spacing should be half of wavelength, in case of BLE, it would be 2.4GHz thus the spacing should be 6...
