Hi Nordic team,
I'm currently working on a real-time distance measurement project using channel sounding with the nRF54L15 DKs. I’ve been using the channel_sounding_ras_initiator...
Man,do you have the experience on DIY Bluetooth headset with PCA100059?
I raise this question for I hate the current product limit: limited time to run,short lifetime of...
Hello, I'm trying to perform a firmware update using the FOTA feature on the nRF7002. After building and running the firmware update code, the following error occurs:
...
I attempted to create bluetooth central and peripheral apps using two nRF52840 boards that connect to each other and no one else using the device name. I had limited success...
Hi, We have used nPM1300 on our development board around nRF54H20, but we are experiencing an strange issue. - when power is attached VBUSINILIM0/VBUSINILIMSTARTUP value is...
Hello Nordic,
I am looking for a sample or instruction (step by step) for custom bootloader.
Our application code is ready and all the left thing is BLE DFU and custom...
Hey All
Im working on a new product and its the first time I'm developing around the nrf5340, I'm looking for some guidance around the supply configuration for maximum...
After reading devzone.nordicsemi.com/.../is-there-any-differences-between-nrf51822-and-nrf51922 and the literature around nRF51922, I'd like to know if there's going to be...
Hi,
I've developed an application which sends sensor data through the BLE interface at maximum available bandwidth by checking the BLE_ERROR_NO_TX_BUFFERS return value...
Hello,
I was wondering if anyone has had success communicating with the nRF24L01+ eval kit and a Raspberry Pi. I have found several examples through Google and am trying...
I am requesting the softdevice to start/keep the 16Mhz crystal oscilator running with the following code:
// Request 16 MHz crystal oscillator
err_code = sd_clock_hfclk_request...
Hi,
I have Nordic Nrf51822 custom board.
in that we have spi Nor flash.
i check the spi read and write with an application without soft device enabled.
which is...
Hi all,
I'm having problems when linking my code intended for use on the nRF51822. For some reason there are missing symbols that are needed. I've traced the dependencies...
Hello,
Does Keil's Lite/Evaluation MDK-ARM tool chain version suffice for development work on nRF51 devices? Please advise!
I have seen questions about using GCC and...
I'm using the s110_nrf51822_5.2.1_softdevice with the NRF51822. If I understand correctly, after pairing the NRF51822 with a phone, a long term key has been generated and...
Hello,
I decided that bonding (does it equivalent to "pairing"?) is not allowed in my application, so I modified the following definition in main.c:
#define SEC_PARAM_BOND...
We are trying to get the ANT feature to run based on RTC as follows:
a. Timer RTC0 or 1 (1 for this example - tick is disabled, compare is on.)
b. Timer initialized (all...
Hi,
I'm a new learner for the nrf51822. In the SDk ,there is an example of esb which is used for the radio transmittion with ACK. I want to know that if I can use the esb...
We have a custom board designed based on N51822, CEAAB0 and we have used the chip antenna from ST BAL-NRF01D3. When we have flashed our proximity code to the device, we will...
Hi,
After i use sd_ble_gatts_hvx() ,i will receive a BLE_EVT_TX_COMPLETE.
The "tx_complete.count" is no problem when i use softdevice 5.2.1 . e.g. count =1. this is correct...
Dear Sir,
i am using pca10001.
Actually i tried to read and write the data from EEPROM having address 0x50 though i2cbus.
i made po.0 and p0.1 as output pin then...