Hello everybody,
for my project, i will bond the peripherial with the central.
I test my device with the MCP and can connect without problems. When i press the Bond Button...
Hi all,
I am trying to count the positive edges of a 3.5MHz signal with GPIOTE, PPI and the TIMER1. Unfortunately i can only measure to frequencies up to a little more...
Loaded Softdevice S140, ( Using NRF52840 DK board ) using NRFgo Studio.
App flash base is set to 0x00021000 and app RAM base is set to 0x20003000
Looking at the CPU...
In our earlier projects with nRF51 and SDK 8 we used to have bluetooth device names of length 13 or 14 characters. However, when using nRF52 and SDK 12 I noticed that the...
Does the Antenna in this Beacon relates with this "BAL-NRF02D3 '50 ohm balun transformer for 2.45GHz ISM"? Any idea what's this "BAL-NRF02D3" for? many thanks!
I am using a eeprep tool which can only be used with command prompt. I am struggling with it.
Here is the format to use eeprep tool :-
usage: eeprep [options] <infile...
Description : It is not possible to flash or debug an application with IAR on the Nordic target. This issue is caused by a bad interaction between CMSIS-DAP IF present on...
Hello guys!
I have a strange problem where the nrf9151dk suddenly won't power up. It was working fine - I was only working with SW, not HW.
I got a pop-up error saying...
Hi Noridic team,
I have enabled Matter over Thread on the nRF5340. In this setup, I'm planning to reduce the TX power by setting CONFIG_OPENTHREAD_DEFAULT_TX_POWER=0. Apart...
Hi,
I have a question about FOTA jobs with queued and failed devices.
Let's say I am managing a group of 10 cellular devices (nRF9151) through the nRF Cloud UI. I create...
Good day,
I am currently working on a project involving the nRF54 series and would like to inquire about support for the NEC infrared (IR) communication protocol. Specifically...
I'm testing my code based on nrf5SDK v17.0.0 with nrf52832 board.
By nrf connect application,I can see the broadcast packet from my board.It looks something like this. ...
Hi I'm working with nrf5340 dk. I have a serial app (on windows) that is doing serial write continuously to the nrf5340 dk but it is not capturing all the data that I'm sending...
Context
We are working on a project that implies advertising and scanning extended advertised packets.
details :
NRF52840
Zephyr SDK 17.0
Zephyr 4.0.99
NRF SDK...
I am trying to port code I developed on the NRF52 DK to a MDBT42Q-512KV2 BLE module from Raytac I purchased from Digikey and am running into problems.
I developed all the...
Hello,
I'm working with a custom board, using an nRF5340 (NCS v2.7.0 but also tested with version 2.9.0) and a W5500. I'm trying to run the DHCPv4 client test just to verify...
Dear Nordic company,
I have question connected with nrf9151 chip. I know, that this chip contains two parts, ARM core and modem.
I am trying to understand of Serial...
Is there a sample app that uses the Zephyr Light CTL Bluetooth Mesh model? I've tried to add that model to the light_ctrl sample app, but get a crash during configuration...
Hi,
The nRF Connect Extension on my Windows VS code doesn't load altogether:
I uninstalled VS code - including all it's settings/extensions etc using this post's suggestion...
Hi,
I can build and program the broadcast_source sample application using the Python script:
This runs fine and broadcasts as expected. However, I cannot get the application...
Hi, I'm working with the nRF9151DK and Zephyr RTOS (v3.7.99 / NCS 2.9.1) . I’ve configured UART1 to send and receive data via GPIO pins:
TX: pin 8 (P0.08)
RX:...
