We are using nRF51822 for our products.
We want to know the min value of "Receiver sensitivity" when we use this chip for BLE.
The Datasheet says "Receiver sensitivity...
Dear
The BLE Multi-link example (ble_app_multilink_central and ble_app_multilink_peripheral)
shows how one central device can connect to multiple peripheral devices. ...
In the MCP app, if I have the following service data for an Eddystone beacon:
0x10, // Eddystone-URL type
0x00, // TX power in dBm. This is a signed integer so 0xEE ...
I have the nRF Control Panel Android application. It works fine with several BLE devices, but specifically for the Fitbit Flex, it fails to connect.
I know Fitbit wristbandes...
Hi,
The situation:
I was able to successfully receive known packets from a device running gzp_device_dynamic_pairing, from, the host running the gzp_host_dynamic_pairing...
Hi everyone
nrf51822,softdevice s130 2.0.0
now i used softdevice s130 establish two connection as a central with two s110 peripheral device,at the same time i establish...
Hello.
This ticket was derived from another ticket .
I have a few questions about hardware-based downgrade protection.
About the Downgrade Protection of the Network...
Hello!
I’ve been learning about Bluetooth Mesh recently, and I’ve been testing the sample at nrf\samples\bluetooth\mesh\chat , but there are still some parts I don’t quite...
I'm using these devices for a personal project, I'm an experienced software engineer but relatively new to MCUs, I know this is a legacy product from Nordic's standpoint but...
I'm an experienced HW engineer with minimal SW experience. I just went through your SDK fundaments with an nRF52840DK to get acclimated to your SDK and brush up on some C...
This stopped working for me... Error is the following
Command failed: git ls-remote --tags --heads github.com/.../sdk-nrf
fatal: unable to access ' github.com/.../'...
I am a beginner to BLE Communication ,
Currently I am working on a project where I need to connect a peripheral device ( Central (nRF52840) ---> Peripheral (BLE device)...
Hi all,
I may have encountered an issue with nrf9151DK board.
When I only set LED1 with dk_set_leds (DK_LED1_MSK) the LED1 and LED2 are both lit.
Setting other leds...
im looking for a developer that can help me work with the NTN functionality of the 3GPP release 17 of the NRF9151-DK so if you are interested please write to me at eric@zerocool...
Hi everyone.
I am using Visual Studio Code. When i try to compile a simple blink_pwm project, I could not. I am sending output in terminal. What is the main problem and...
Hello!
I am working to design and build a custom PCB using the nRF7002 chip and came across this callout on the schematic diagram and wanted some clarification about it...
Hi,
I designed a custom PCB with the nrf5340 CLAA chip and am testing out the board. I want to flash a simple project of lighting up the on-board LED (the LED is connected...
Hi, I'm currently working on an application with the nRF9151, and will use the shadow concept to change parameters used by a device externally connected to the nRF9151. Intended...
i'm already able to TX and RX arbitrary packets between my own bare-metal test programs running on a pair of DKs... since both programs used identical configurations (mode...
Hi,
We are on NCS v2.9.1
We have an existing project on based on the nrf52832, which we use as a hci_spi controller. There, CONFIG_BT_LL_SW_SPLIT is set. We are now porting...
Hi Support Team
We try to integrate the flowing links' sample code of Mesh Sensor, Mesh LPN and Mesh DFU to one project for nRF52832, but we found that the memory usage...
