Hello,
Connection between linux router and NRf51 devices worked before I've updated kernel version from 4.09 to 4.3.
Now, with the same configuration and hardware, I'm not...
Hello,
Connection between linux router and NRf51 devices worked before I've updated kernel version from 4.09 to 4.3.
Now, with the same configuration and hardware, I'm not...
Hi
Does anyone know a CE—certified module based on the nRF24LU1+? Ideally, it should have an SMA connector, but any kind of antenna would be fine.
There are many modules...
I am running peripheral example radio test example on PCA10001(part of nRF51822 Evaluation Kit). using nordic sdk v7.
I am using mincicom on linux at baudrate of 38400...
Hello!
I am trying to get windows phone work with nrf_uart example on nrf51 dk board (pca10028).
I am using SDK 9.0 with S110 softdevice ver. 8.0.0.
I was using examples...
Hi
I met a problem when I use my new board,I found that the example in the peripheral folder in SDK can run correctlly,but the the example in the ble_peripheral folder...
Hi,
I am trying to use the PORT event to trigger interrupts when a button is toggled, i.e. both on LoToHi and HiToLo.
To my understanding PORT events are generated by...
I'm using nrf52840 dongle. followed setup based on
https://docs.nordicsemi.com/bundle/nrfutil_ble_sniffer_pdf/resource/nRF_Sniffer_BLE_UG_v4.0.0.pdf
https://www.youtube...
I am trying to use the FIFO from the ADXL362 with in the Thingy:53. As I noticed there is now the Option to use ADXL362_STREAM. I just wanted to use the example from: https...
Hi,
The Thingy 91 X uses a shared antenna for BLE and Wi-Fi. I can see from the Hardware Guide and the schematics that there are several hardware connections between the...
Hi,
I am working on implementing the BME680 sensor with the nRF5340DK using the I2C protocol. I have successfully obtained the slave device address and the sensor address...
Dear Team,
I am experiencing issues updating the firmware image on my custom board based on the nRF7002, using an external SPI NOR flash ( is25lp064 , 8MB). The board...
Hello, I’m trying to compile code for a u-blox C209 AOA Tag. I installed the nRF Connect Extension Pack and was able to build normally.
After adding some unrelated paths...
As part of a university project I am trying to read an analog signal and transmit it at the maximum data rate over ESB. But I cant seem to get above 1700kbps without any of...
In https://docs.nordicsemi.com/bundle/ps_nrf54L15/page/uicr.html#register.BOOTCONF, I can seee that it is possible to apply Read protection to the first x kB of the RRAM by...
i have some bare-metal RF code that runs on my nRF52-DK, which i'm currently porting to my nRF54-DK.... functionally, everthing is working just fine -- the boards can in fact...
Hi
I am trying to port some PWM code from the NRF54L15 it uses HAL access because i have found it has faster writes which are useful for my application (testing latency...
I implemented the function of DFU using NRF SDK 17，Implemented dfu using MCUboot with ncs 2.9.0
Can the dfu of MCUboot in ncs 2.9.0 upgrade the program of nrf sdk 17
I'm hitting a wall with implementing nRF7002 + nRF52840 without Zephyr.
I've worked with nRF52's for about 8 years now and on about 30+ products, all using the original...
Hi, I'm using the nRF52840 DK with SDK 17.0.2.
I've set selective_auto_ack to true , which should allow the use of dynamic ACK (or ACK payload).
I have two types of data...
Trying to get set up with my new PPK2. Installed NRF Connect and JLink on my Win11 system. When I select the device in the Power Profiler software I get an error. Searching...
Hello,
I am trying to download nRF Connect for VS Code extension but the extension is not found. There is just no result when searching for 'nrf connect' or something...
