Hi,
We're planning to design a custom board using the nRF9151 for LTE connectivity. We'd like to add basic BLE support, with the following constraints:
The BLE chip...
Hi,
I am trying to set up a project that continuously measures the pulse width of a signal that may or may not be present at a pin.
I want to use a Timer in capture...
hi
after success dfu operation the firmware start to run
then i am getting stuck write after err_code = sd_ble_gap_device_name_set(&sec_mode, new_name, DYNAMIC_NAME_LEN...
I've been following the information on the nRF54H20 with interest as it is most likely the natural candidate for upgrading our existing design. However, I have been waiting...
We are developing an application on nrf52840 and wanted to use M95P32 as external flash.
used below .overlay configuration to enable it on zephyr.
&mx25r64 {
compatible...
Hi,
Using nRF Connect SDK 2.7.0 on an nRF9160. Using native tls, works fine, i can setup HTTPS connections.
Problems arise when i try to use MQTT with native TLS (with...
Hello Nordic DevZone community,
I have been working with the ZBOSS stack on the nRF5340 and understand that it has version management and migration features for persistent...
Greetings, and thank you ahead of time to anyone willing to lend some advice.
I'm implementing application-layer security by requiring central devices to supply a user...
Hi,
I am having some trouble getting the nrf51422 (running the s130 soft device) to wake up after entering sleep mode. I have successfully entered sleep mode using NRF_POWER...
Hi,
I am trying to work with ble_radio_notification.h. When I import this file to my main.c, I have "No such file or directory error". When I try to add it to nRF_BLE folder...
Hii every one,
We are working on a project where we are using a temperature sensor LMT01, its giving a pulse output the pulse out is from 220mV to 600m. So I'm using lpcomp...
Hi,
I am getting only two values on startup and the remaining values as zero when using app_timer_cnt_get.
EDIT: updated entire main.c file
#include <stdint.h>
#include...
I am trying to bring the pc-ble-driver code up on a single processor ARM based board with Linux build under Yocto control. The boost library version being used is 1.60.
...
Hi All,
I'm implementing system clock using approach similar to
devzone.nordicsemi.com/.../
The idea:
NRF_RTC_EVENT_COMPARE_0 -> PPI -> NRF_TIMER_TASK_COUNT
...
I have a nRF51822 custom board for BLE UART application. Connects this to serial port of an ARM SoC board.
P0.09 is for UART_Tx and P0.11 is for UART_Rx. No RTS and CTS are...
i am using a blend micro with nRF8001. and i am using it as a hub in my project.Now i am getting a range of 13 meters.but that is not enough for my project.so can i increase...
Hi!
I'm using the nRF Sniffer software (Windows 1.0.1 Rel.1111) with nRF51-DK Board (Rev. 1.1.0) and Wireshark (1.12.5).
Everything works fine until the number of 65535...
hi
i work in sdk v6.1 and work with dfu over air and it work fine on s110 but now i open this project
nrf51_sdk_v6_1_0_b2ec2e6\nrf51422\Board\nrf6310\s310\ble_ant_app_hrm...
Hi!
Turns out that there is no need for the SD310 and the nRF bootloader. Which means that the flash layout is edited and current support for the BLE OTA is dropped since...
Hi,
I am working on nRF51822 Microcontroller. I am not using any kind of stack I mean Bluetooth etc. I have a simple nRF51822 microcontroller and am running a simple application...
Like the title says, I'm making a call to nfc_t2t_emulation_start, and getting NRF_ERROR_INVALID_STATE (0x08) back.
The only prerequisite that I'm aware of in order to...
