I have installed Keil MKD-Lite V 5.10.0.0 and the Segger software (which linked to the Keil IDE). I have tried to install the nRF51 SDK (5 times) and every time iI get the...
Hi,
I am attempting to get the DFU working as per the example provided in the S110 V7.0.0-3 download. I've followed all the steps in the readme in the DFU subfolder and...
Hi all,
I have an application where an nrf24le1 is communicating serially with another processor, using the UART at 57600 bps. I have multiple identical boards communicating...
after flash DFU program into pca10001 board, com3 is not accessible,
www.dropbox.com/.../Screenshot 2014-04-26 15.41.47.png
even after I erase all, and re upload soft...
Using S120 V 8.0.0.3 alpha, processing a BLE_GATTC_EVT_READ_RSP,
received 0x16 bytes of data but there is more to read. Next call to
sd_ble_gattc_read using the same connection...
Hello：
Why Bluetooth Go to system-off mode, sd_power_ramon_set can not be stored. In D: \ RAM save nrf51_sdk_v5_2_0_39364 \ nrf51822 \ Board \ nrf6310 \ s110 \ ble_app_rscs...
Hi,
Recently I want to set up a dynamic network that with the node change this position ,the network will change dynamically.But there is the question,with the node's position...
Hi
According to BT 4.2 Spec Vol 6, Part F, Section 3.2.9:-
" To write the entire value of an attribute larger than (ATT_MTU-3) octets, the prepare write request and...
hello,
i have a rather basic question concerning the design of the cycling power measurement value field.
how does a simple example for this value look like (variable...
What is the difference between SDK 8 and SDK 12 related to app_timer? I have used it like:
APP_TIMER_INIT(
APP_TIMER_PRESCALER, APP_TIMER_MAX_TIMERS,
APP_TIMER_OP_QUEUE_SIZE...
Hi Nordic,
I have a star network with 3 nodes and 2 channels. I go through the whole pairing process and start sending data without problem. Now I want to, from the master...
I would like to advertise two different sets of data in parallel, such that one ADV packet is ongoing (say, A), and then I switch to the other packet (say, B) with different...
I tried to make android app for nrf51822 hrm proj.The app flows like this: scan--connect--discover service-- setnotification for every characteristic. The Hrm char was firstly...
Hello,
Could you please advise where I can download an older versions of nRFgo Studio that supports nRF24LU1P? I've got a USB dongle, which I need to re-program.
Thanks...
Hi
I use ble_app_hrs_rscs_relay example with sdk12
and when the APP_ADV_TIMEOUT_IN_SECONDS is reach the nrf52 stop advertising but the on_adv_evt has no BLE_ADV_EVT_IDLE...
Recently I had some strange bugs in few production devices. I inspected newer device markings and they look a bit different:
Pin 1 marking is square not circle.
Build...
Is it safe to use a larger capacitor on the DEC4 pin when using the internal LDO only configuration? So instead of 1.0uF say 4.7uF? Just trying to remove one line item on...
Hi, I need to make a BLE system which sends ADC values from a chip to a receiver kit.
The example most closely resembling this functionality seemed to be the heart rate...
Hi!,
UART works fine with nrf-ble-tutorial-characteristic-CompletedCode in my nRF51-DK but I'm trying to implement in my application but not works.
These are my includes...
Hi,
I am using nordic nrf51822 ble device and I am using bluzDK-firmware from
github.com/.../bluzDK-firmware
I want to add passkey in this firmware. Please help...
