Hello everyone,
I’m working on a project using two nRF5340-DK boards to measure throughput and RSSI while dynamically changing the PHY and TX power. I started from the official...
Hi,
When i want to connect my Power profiler kit II to my laptop, it first blinks GREEN. After i connect to it using the power profiler app, it goes: RED -> AMP (Ampere...
I have a custom board with a nRF5340 and need to configure VREGH in DC-DC mode and set 3.0V output on it.
I see the documentation on REGULATORS — Regulator control where...
Hi,
NRF54L15, nordic sdk version 2.9.1
I recently lost ability to build my application. I get this linker error:
/home/adam/ncs/toolchains/b77d8c1312/opt/zephyr-sdk...
Hello,
Now, I currently run Asset_Tracker_Template on Thingy91X
https://github.com/nrfconnect/Asset-Tracker-Template/blob/main/docs/common/getting_started.md.
And, I...
Hi,
I have autoprovisioned and autoconfigured my nrf52840 board (provisioning and configuring are made inside the software and not through external app/provisioner).
In...
Hello Nordic Team,
Currently, we are performing power consumption testing using the Nordic nRF54L15-DK development kit.
As part of this, I aim to fully disable the Radio...
I use SPI connection according to the table .
I want to press the button 4 on tx (P.06) to transfer "hello", to write down the answer of rx(P.08) in the file on sd card in...
Hi
I'm using nrf51 to notify some data to an andriod device. I set the connection interval of my nrf51 program to 7.5ms. And I need to send 100 packets per second (20 bytes...
Hi Admin.
How can i calculate distance using RSSI. is there any existing method available? i tried statically(like 35-40=1m 40-45=2m) but i dont know actual method to get...
Hi all,
I am trying to add the iOSDFULibrary library to an existing Objective-c project via Cocoapods (Xcode 8.2.1 - target iOS 10).
I have followed the steps reported...
Hi
I've just done a few tests with the FDS system of the SDK12.2. My observation is, that the FDS doesn't properly use all assigned flash pages to reach a maximal lifetime...
Hi,
I am quite new to nRF51 development so please excuse me for my mistakes or not using right words if any. I have some code that fully works on the official nRF51 DK...
Iam using softdivice 110 and sdk 10.0.0, when i connect UART RX pin to TX of STN1110 the processor doesn't start until I remove connection between RX of nRF51822 and TX of...
Is this antenna pattern and design for our custom board is fine? we are using the nrf51822 with matching circuit.
Please put your valuable suggestion from your experience...
Hello,
I am using nrf5 sdk 12, and I have read the documentation in ble_gap.h for NRF_ERROR_INVALID_STATE and I have seen a few questions on this forum, and what I understand...
I have an application (with SD S212) that uses NFC. Ideally, the processor would be in idle most of the time, waking up only to FIELDDETECTED and FIELDLOST events.
The...
Hello,
in nRF52832_PS_v1.2.pdf, in the timer section for the MODE register, there is a third mode named "Low Power Counter" described, without any description in the rest...
Dear Everyone.
Hi, I develop nrf51822 with DK PCA10028. I have been optimizing the power consumption to some extent. But now I am very confused.
I use S110 softdevice...
Has the nRF51822 already got the QID and BQB certificate? Our BLE module using nRF51822 doesn't do the QID and BQB test. Can our product using the BLE module add the BLE logo...
Hi,
We need a 2.4Ghz smd antenna, not to emit bluetooth but a in-house protocol we are testing.
It will need to fit on a pcb and have good performance, and production...
