There is the board mark on the chip like n51822CEAAD01350A0, where DO is Build code, 1350 is tracking code(YYMM), A0 is lot code.
My question is how can I get those codes...
I'm trying to debug a randomly occuring Hardfault. In trying to trace down the source I read the CPU registers use the Nordic hardfault_implementation.c which grabs the register...
Dear nordic employee
my purpose is send a data the length is from 150 to 273
when my server device send data by sd_ble_gatts_hvx（the send length is fixed 10 bytes） ...
Dear nordic employee：
The service I want to find is the sound service of the thing52 thingy sound service
I tried to modify the HRT_central_client project to find the...
When I was using the device as peripheral, I was wondering when the Softdevice notified BLE_GAP_EVT_SEC_PARAMS_REQUEST and BLE_EVT_SEC_INFO_REQUEST:
1, when peripheral...
hi dear nordic employee:
I tried to build the project ble_app_hrs_c（pca10040） by keil5
but I get an error :
._build\nrf52832_xxaa.sct(7): error: L6236E: No section...
Hi,
I am a bit confused about power consumption when using app_uart_fifo. To save power I put MCU to sleep in between each sent and received byte by using __WFE and __SEV...
Hi,
I want to know that how if we have Beacon on one side and Development kit on another side so it is possible to communicate them if they are using different services...
I'm using nRF SDK and trying to write firmware to my prototype device. However, nRF SDK doesn't detect my prototype device. I checked the power supply to my prototype device...
Hi,
I am testing example from sdk, 12.2.0, ble_app_uart, nrf52832
And i frequently get a strange behaviour where i don't get a response. And the connection is terminated...
Hello,
I'm trying to set my device on DFU mode by an android mobile application without success.
I'm working with nrf51822, sdk10, softdevice 8.0.
I subcribe to the...
Hi.
I'm using PCA10028, SDK12.2.0, S130 as central.
As I know "sd_ble_gap_tx_power_set" function let me set Advertising Tx power.
How can I set Tx power if i want to...
Hello,
I am going my project with NRG51822 in SDK 11. I build a android app that can connect to my device and access vendor specific service.
My device dedicates one...
Hi, All,
I'm testing multi-connection central function.
And I am struggled in getting relation of address.
AFSK, there are several types of address in BLE.
I found...
Hi.
I'm using nRF51822AC, SDK12.2.0, S130 as central.
After "sd_ble_gap_connect" function, how can I stop this function before connection?
I hope your reply.
Hello,
Is there a way to temporarily disable bonding and just allow any connection? I want to generally use bonding, but there are certain corner cases where I need to...
Hello,
I want to use the FDS libraries in order to store some data into nrf52's flash in my application and I have a bootloader to allow secure dfu by ble.
I manage...
I'm struggling with current consumption. I need my device to completely sleep and leave only the RTC on when the ext power is off (run on battery). After making sure my RTC...
Hy everyone!
I'm trying to write a non-volatile memory position of a device via I2C (twi), the device, a flash memory is the slave.
In my application, I have configure...
Hi I am using the SDK 12 and I am doing some test using the experimiental_app_ble_blinky central and peripheral parts.
I see in this example it use boolean values to indicate...
Hi,
I am using the experimetal app_ble_blinky on both sides peripheral and central.
I edited the peripheral characteristic sizes to 4 and I am able to send notification...
