I am working on a project using a ble nano (nrf51822) using the Nordic SDK 8.1. In the examples I found a way to control an LED using the methods LEDS_ON and LEDS_OFF. I wanted...
Hello,
I am using ble_app_gls example and I have implemented static passkey in the code. Now I want to see if wireshark shows the passkey when I connect to ble devices. For...
Hi Team,
We are implementing an UART communication between a M4 processor (UART master) and a nRF51 (UART slave) and we want to use the UART in Low Power mode with flow...
Hello everybody,
for my project, i will bond the peripherial with the central.
I test my device with the MCP and can connect without problems. When i press the Bond Button...
Hi all,
I am trying to count the positive edges of a 3.5MHz signal with GPIOTE, PPI and the TIMER1. Unfortunately i can only measure to frequencies up to a little more...
Loaded Softdevice S140, ( Using NRF52840 DK board ) using NRFgo Studio.
App flash base is set to 0x00021000 and app RAM base is set to 0x20003000
Looking at the CPU...
In our earlier projects with nRF51 and SDK 8 we used to have bluetooth device names of length 13 or 14 characters. However, when using nRF52 and SDK 12 I noticed that the...
Hi,
I would like to know, by using nRF528322 Development Board can we dump the code into another hardware like custom nRF51822 microcontroller..??
If Yes, What are the...
hi , need a urgent help on small problem but really not getting ahead bcos of it.
I'm using NRF52, SDK v11 , Software Device s132.
I'm calling sd_ble_gatts_value_set() like...
The struct type nrf_saadc_config_t is defined in ../hal/nrf_saadc.h but is not referenced anywhere else in SDK v12. Thus it is either cruft, or more likely, the function nrf_saadc_init...
Hi.
Is it possible to use SPI slave and SofDevice at the same time? I try to do device which status will be read by master uc by SPI. I'm using nRF51422(rev.3), SDK10.0...
Hi All,
I am working on nRF51822, i have questions about BLE passkey security:
1- The pass key is for GAP or GATT services?
2- The BLE have few layers of data: Profile...
Could you confirm s130 data for Segger Studio Section Placement Macros FLASH_START=0x1b000
SRAM_START=0x20002800 ? This works for sdk11, somehow goes to hard fault handler...
I have impleted s110 DFU in my products,there is not any proble.But when I transplant it to the S130,it can't work.I checked the code,I found S130's DFU is different with...
This page www.nordicsemi.com/.../nRF5-SDK-for-IoT contains a link to the iot sdk doc which in fact leads to nowhere: infocenter.nordicsemi.com/.../iot_sdk.html
My browser...
Hello,
I am having an issue with the DFU in SDK V12.
Using the secure_dfu package, and the buttonless dfu app as a template, I was able to get OTA DFU application updates...
I developed an android phone application base on the source code that was provided by nordic. Now I am trying to develop a PC version of what I made on the phone for lower...
Hi,
I am using NRF24L01+ as wireless communication medium. The NRF on PRX side interrupts MCU only once for recieved data. Although it sends ACK to NRF at PTX side. And I...
Hi,
I need to read data from MLX90615. It is a temperature sensor which follows I2C to read data. I got a sample code for this which is given below.
float receiveTemperature...
Hi all,
context: nrf52, iot sdk and ipv6; initially rpi as "border router"
question: What can be used as professional/industrial "border router" instead...
Hello,
Arduino start selling Arduino 101, powered by an Intel Curie processor.
As far as I have seen here , Intel Curie module integrates nRF51822.
I was wondering...
