Hi,
I want to use the Blend Micro with more security. I want use a passkey for the Bluetooth connection. For example through the iOS Device.
Is it possible? Static passkey...
How do I receive multiple signals simultaneously at a single receiver (433MHz) with multiple transmitters ?
I am working on a polling system. This one is similar to the audience...
Hello,
I established a connection between my central and peripheral module. Now i want to write characteristic value on peripheral. I tried with sd_ble_gattc_write function...
I am using the NRF24l01 for my products and looking to buy in bulk(100-1000). Now I know where to buy the just the IC but antenna design is a hard point to break right now...
Hi, my friend,
I've been with nrf905. I use a 16-bit CRC check.
But I encountered problems in use:
1.Nrf905 16-bit CRC check format is CRC-16(IBM):X16+X15+X2+1 or other...
I have two custom PCBs, each of which has a microcontroller and an nrf24L01+. Everything related to the transceiver in the designs are complete duplicates (with the exception...
Hello,
I've built a small BLE-device based on the nrf8001.
With my Iphone I can discover this device and I am able to connect to it and listen to notifications of the...
Is there an event that I can hook into that fires when the soft device has finished it's connection and negotiation with the phone and is ready to send data to the phone ...
Is there any way to get some "modern" content assist features in µVision that work with the Nordic SDK? If they're there, I haven't had any luck finding them. After having...
I'm trying to decide whether to use FreeRTOS or simply build on the Scheduler. What are the risks and benefits of using freeRTOS or another RTOS on a wearable sensor device...
Is it possible to connected two separated antennas (single ended), one for RX and another for TX communications to the receiver and transmitter of the NRF51 or NRF52?
Thanks...
In other words, is it safe to assume that in various BLE events, conn_handle is either invalid (0xFFFF) or between 0 and (CENTRAL_LINK_COUNT + PERIPHERAL_LINK_COUNT - 1) ...
I'm digging my way through the examples, SDK code, etc, and I'm curious if it's possible to light an LED if the nRF52832 is reaching an error status. This is mainly so I can...
Hello,
I am seeing a strange problem with the nRF52 RADIO peripheral: sometimes a packet will be received that is corrupted, but the CRCSTATUS register indicates the CRC...
My company is developing an embedded product based on NRF52 and until now we are
using Master Control Panel (MCP) to test BLE communication. MCP is a great tool
but we need...
Hi,
when trying to connect to a 51822 target, using for example OOCD
I keep getting
....
Open On-Chip Debugger 0.10.0-rc1-dev-00001-gc404ff5-dirty (2016-12-29-19:45...
I use PPK wit ha stardard setup with all switches set to DK. Everything works fine, excepted that I have a little offset and the IDLE state is negative... which make the AVG...
I have designed a few PCBs using the NRF52 chip with a standard QFN48 pattern. On the first design, we had 8 PCB's made of which, only 2 worked correctly. The others all exhibited...
Hello,
I received BLE_ERROR_GATTS_SYS_ATTR_MISSING event during connection procedure. Tried to look inside and found
/**@brief Event structure for @ref BLE_GATTS_EVT_SYS_ATTR_MISSING...
In code:
case PM_EVT_BONDED_PEER_CONNECTED:
NRF_LOG_DEBUG("Connected to previously bonded device\r\n");
err_code = pm_peer_rank_highest(p_evt->peer_id);
i get...
