Hello,
I am using nrf51422 with stm32L0. There is a uart connection between nrf51422 and stm32l0. I want to transfer data from stm32l0 to nrf51422 through usart and push...
hi........... folks
i am merging two programs together uart and TWI sensor ...using nrf52382 and segger 15.2version
i am getting the error in ble_nus_send ,
even i have...
Software and Softdevice: SDK 12.3.0 keil5
Platform: Windows 10
Hardware: NRF52832 DK
I am trying to combine WDT and FATfs together. But once I have both of them, there...
I am trying to get a good handle on the difference in average power consumption between BLE point to point and Zigbee on an nRF52840. We have battery powered products and...
Hi, For my project, I need to design a BLE packet sniffer which scanning the 40 channels. Therefore, I need 40 dongles are connected to a computer that can read and transfer...
I am writing code to get a nrf52840 DK to associate with an existing 802.15.4 coordinator using the 802.15.4 API module within SDK 15.2.
I've called "mlme_scan_req" and...
Currently, I am able to use Mqtt Publisher or Subscriber with only one Nrf52 device. I can ping to the device with link-local address.
I am using Nrf52832 with SoftDevice...
I am receiving the above error when trying to create a destination under "Device Management -> Message Routing Service -> Add Destination". There is no further indication...
I was following instructions from this and this post, but I'm not yet able to build with the following combination: CMakePresets.json + west + sysbuild.
I'm using this west...
NPM2100 EK CONNECTION
Can I connect The NPM2100 EK with NRF52 DK? If so..... 1. How do I physically do this? 2. Can I program the NPM2100 EK to send Voltage Supply of 1...
Our design has an nRF5340 with RV3028C7 to provide the 32 kHz clock via P0.00.
If I configure P0.00 as a digital input, I can see the pin toggling.
However, if I use the...
nRF52832, SDK17.1, s132 I work with SPI and it works on the this project with SDK15. But I have transferred this prj to the SDK17.1 and I can't make SPI work. I don't get...
I'm trying to convert some code from ESP32 to nRF, and I'm having problems with the microphone input. Mind you, I'm a beginner with nRF, so I'm sure I'm missing something...
Hi,
I got my hardware modification which added the nRF21540 to our system more or less running under NCS v2.9.0.
Currently, I have the following FEM and antenna configuration...
Hi,
I am trying to use mcuboot to load a version that is stored in my external flash, and I cannot get it to boot. My project is being built using sysbuild and my target...
Dear Onomondo Support Team,
I am currently experiencing an issue with my Onomondo SIM card — it is unable to register on the network when used with the nRF9151 DK board...
Hello,
I am trying to play the AT45 DataFlash driver by directly copying the sample code from nRF connect SDK v2.9.1 (C:\ncs\v2.9.1\zephyr\samples\drivers\spi_flash_at45...
Hello, I am working on a project using zephyr as well as the nrf5340 MCU. For this test, I am on the nrf5340dk. My application requires I drive a PWM at 125khz. In my device...
NCS 2.9.1 - NRF5340 DK
I've developed the gppi one_to_one example to try and create an asymmetric pulse that I can control with the Timer compare registers. It boggles my...
Hi,
I switched to SDK 3.0.0 and got back problem, that I had some time ago with 2.6?? When my code compiles, but controller stuck after many successful builds and I open...
I'm encountering a blocking issue when trying to create a new board using the NCS Board Wizard in VS Code with Nordic Connect SDK v3.0.0. After filling in valid inputs and...
Hello,
I'm having a serious issue with my nRF52840 board. Here’s what I already tried:
What I have done:
Verified working USB cables (data + power).
Installed...
