Hello,
I am using nrf51422 with stm32L0. There is a uart connection between nrf51422 and stm32l0. I want to transfer data from stm32l0 to nrf51422 through usart and push...
hi........... folks
i am merging two programs together uart and TWI sensor ...using nrf52382 and segger 15.2version
i am getting the error in ble_nus_send ,
even i have...
Software and Softdevice: SDK 12.3.0 keil5
Platform: Windows 10
Hardware: NRF52832 DK
I am trying to combine WDT and FATfs together. But once I have both of them, there...
I am trying to get a good handle on the difference in average power consumption between BLE point to point and Zigbee on an nRF52840. We have battery powered products and...
Hi, For my project, I need to design a BLE packet sniffer which scanning the 40 channels. Therefore, I need 40 dongles are connected to a computer that can read and transfer...
I am writing code to get a nrf52840 DK to associate with an existing 802.15.4 coordinator using the 802.15.4 API module within SDK 15.2.
I've called "mlme_scan_req" and...
Currently, I am able to use Mqtt Publisher or Subscriber with only one Nrf52 device. I can ping to the device with link-local address.
I am using Nrf52832 with SoftDevice...
How can I differentiate between a brown-out and an initial power-up on the nRF54L15? In my project, I need to detect a brown-out event in order to trigger specific actions...
Hello Nordic team,
I would like to automatically patch the merged.hex file each time I build my project. I’ve attempted to use extra_post_build in CMakeLists.txt , but my...
Hello, we are developing a BLE application using nRf52833. Because of the waterproof & stainless steel casing requirement with rechargeable battery charging capability, we...
Hello
I am using the nRF7002-dk board for my project. The main goal is to be able to use Wi-Fi and also a 2.4GHz proprietary protocol for low latency communication between...
We have a design in EVT and we're preparing for FCC testing. It's a dual radio board with nRF52840 and a Semtech LR1110. Therefore, we need both to be active and transmitting...
Hello everyone,
I'm developing an application using the SX128x radio with the LoRaWAN Basic Modem.
The project runs successfully on a custom board based on the nRF5340...
Hi Nordic Team,
We are using the MIMXRT1050-EVK as the host and the nRF7002EK as the Wi-Fi module with an SPI connection. However, we are encountering frequent errors that...
Hi,
SDK: 3.0., nRF54L15
The application is Matter + BLE dynamic multi-protocol + battery powered sleepy end device. Current Application(Matter/Thread + BLE + Firmware...
I’m using the Zephyr nordic,npm1300-charger driver on an nRF52840 to control the nPM1300 PMIC charger. At runtime I need to be able to turn charging on and off—on command...
Hi everyone,
I'm currently following the "WiFi Fundamentals" course provided by Nordic, and I'm encountering issues with two specific exercises: l2_e3 and l4_e1 . Other...
Hello, I can commission bulb and switch pass, then I refer this link( acl and bind ) to write ACL and binding both, eventually I can use switch to control bulb!
But I have...
My product has nrf52840 with usb mass storage configured using 8MB QSPI flash (same chip as the nrf52840dk - MX25R64)
I would like to allow users to upgrade firmware by...
Hi,
I need to implement low power mode in my project with an nRF52832. From a general perspective, I want to:
1) boot the device,
2) initialise stuff/peripherals,
...
Hi,
I am analyzing the issue that the BLE module can maintain a relatively short connection distance. Besides the transmission power and frequency offset, I also take...
