Hi,
I've been working on a way to detect and prevent replay attacks when beacons are used for sensor data. This is mostly used for home automation sensors, where I have BLE...
Hi,
For our current application we have migrated from SDK 13 to SDK 14. We are using RTOS to handle the functionalities of our application. We replaced our own task for handling...
hello,
I use nrf51822 + S130 + SDK12.2 in my product, nrf51822 work at central + peripheral mode，and i use nrf_duf_flash module for my dfu funtion.
The problem is, i...
I want to communicate Central and peripheral devices with KeyPass. Also I want to generate keypass in Peripheral device. But keypass should to include symbols, low/upper case...
I am using SEGGER Studio on MacOSx.
When use the latest mesh SDK, I can run the light_control example and see the debug log in the Debug Terminal of SEGGER Studio.
However...
Hello,
I'm trying to setup a nRF Cloud Bluetooth gateway using my PC (with openSuse 42.2 64bits and rRF Connect v2.1.0 + nRF Cloud Gateway v0.9.7) and a nRF52 DK and I...
Hello: I am using an NRF51 dongle. Date on the device sticker on the back is 2015.38. Also using nrf51_ble_driver_linux_0.5.0.
I can see/connect to the device I am trying...
We are currently utilizing the nRF5340 with Zephyr OS version 3.6.99-100befc70c74 and nRF Connect SDK version 2.7.0-5cb85570ca43. We have the following inquiries:
If we...
Hello,
To provide some context, I am using an ANNA-B112 with nRF52832 on a custom PCB board we manufactured for evaluation. The nRF52832 is setup with the NUS service with...
Hello,
I’m working with a custom board using the nRF54L15 and the latest Nordic SDK, and I’m facing an issue while trying to communicate with an nPM1300 over I2C.
Here...
As part of a university project I am trying to read an analog signal and transmit it at the maximum data rate over ESB. But I cant seem to get above 1700kbps without any of...
I've been using PPK2 to test our work for maybe around 3 years. it's always been steady and stable and can run for several days without problem. Mostly I'm using the PPK2...
I have problem with i2c that can't read the cst816s, its always return log message `<err> cst816s: failed reading chip id` and `<err> cst816s: Could not read x data` when...
Hello!
We are planning to implement OTA update of an application and a second stage bootloader in our product. As a bootloader chain, we will use NSIB + MCUboot as the nRF...
I am a beginner to BLE Communication ,
Currently I am working on a project where I need to connect a peripheral device ( Central (nRF52840) ---> Peripheral (BLE device)...
Hello.
I tested the DFU distributor sample using two nRF54L15DKs. I have three questions.
1. Apply is not completing. The firmware transfer seems to have completed, but...
I made some tests with PPK-II in source meter mode by connecting a load resistor in series with a Fluke 8846A ampere meter to the PPK output. A also hooked a GW Instek GDM...
Hi Nordic Team,
I would like to confirm whether enabling APPROTECT also implicitly enables Secure APPROTECT, or if these two protection mechanisms need to be configured...
Hi,
The Thingy 91 X uses a shared antenna for BLE and Wi-Fi. I can see from the Hardware Guide and the schematics that there are several hardware connections between the...
Hi Team,
I am currently working on a project involving the Nordic nRF DK IDE and the Matter protocol. As part of my learning process, I watched your YouTube video and followed...
Hello,
I attempted to follow the nrfutil offline install instructions. However, I keep receiving the following error when trying to install the device package on the remote...
I'm an engineer to develope smart ring, it's a very small devie and need to use very small IC.
I'm looking for nRF5340 + nPM1300 reference schematic for this development...
