Hello,
I am using nrf52840 MCU.
I am developing a product which have 2 I2C and 2 SPI interfaces. All the interfaces are on different pins.
I developed this thing with...
Hello all,
I am using the nrf52840 MCU and NCS v2.6.2 for my application development. Here I am using SPIM3. I am using a peripheral which have an internal FIFO. From...
The partition config for ZBOSS is set in different locations in NCS. For us this worked out magically in the past because the values that were written have been the same in...
Hi everyone,
I'm working on a project using the nRF54L05 (v2.9.0) and I'm currently facing an issue with BLE. I want to change the BLE transmit power , and so far I’ve only...
Hello.
This may be a basic question, but please let me know. I am using nRF54L15-DK and nRF Connect SDK v3.0.2.
Is the 32MHz crystal running when the nRF54L15 program...
hi everybody: This is my first time developing an nRF chip and also my first time using VSCode After installing nRF tools and fast (3.0.0), I found that I did not see the...
Hi,
I’m trying to understand the following parameters in the nRF54L15 channel sounding configuration, because their function is not clear to me. I added my questions as...
Hi ,
I have designed a beacon using nrf51422 nordic chip. But when I checked the antenna frequency , i came to know that its above 2.45 Ghz. I tried by the changing the...
Hello:
I open nrf51-ble-tutorial-service-master\SDK 11.0.0\nrf5-ble-tutorial-service\pca10040\s132\arm5_no_packs\nrf52-ble-tutorial-service.uvprojx and compike then find...
hello:
I open nrf51-ble-tutorial-service-master\SDK 11.0.0\nrf5-ble-tutorial-service\pca10040\s132\arm5_no_packs\ nrf52-ble-tutorial-service.uvprojx, and compile ,the result...
Hello,
I am developing custom driver for TWIM. I am facing a problem with DNACK and ANACK which hangs my application. SCL and SDA lines are monitored through Saleale logic...
hello,
again, sorry for the begginers qustion(probablly i will have 2-3(hopefully) in the next few days). I got today the nrf52-dk, and on the back of the nrf52 is written...
I ask the questition yesterday ,maybe i have not expressed clearly.In my project , I have to use three spi in master mode and three twi in master mode to communicate with...
Hi!
In my teamwork we are developing an application for use a sensor module via spi, and share data and comunicate with other devices via Bluetooth.
I've taken care...
Dears,
We are working for a dongle solution to exchange data.
Have any BLE SDK solution via Uart to exchange data between host & client? and that the host is no need...
Hi,
I am using nRF51822xxaa and s130 and SDK 10.0. nRF51 connects with the app(notifications enabled), then bonds with it. Subsequent communications between the app and the...
I connected with RTT Viewer 5.12f with nrf51 DK board.
while I donwload firmware to the board, I got bunch of error message from RTT viewer..and it stop..sometime the download...
I am having two issues with the following code:
When I run this sample code on my NRF52DK (there's external hardware connceted but that does not affect this operation...
Hello, everyone~
I used to see nRF51802 in an official document but cannot find it in the official website. Is there an nRF51802? If so, what are the differences between...
Hello Everyone,
Can anyone give me recommendation of a BLE App for Eddystone TLM (with temperature)?
Till now, I used the Beacon Manager. But I think the App has a problem...
The gpio specifications table lists 3mA for VDD greater than 1.7V and 6mA for voltages greater than 2.7V but what about in between?
Would a linear approximation between...
Hello,
I am trying to fix the UART communication error in a peripheral side.
First of all, the setup that I am using is as below.
[SDK] nRF5_SDK_11.0.0_89a8197
...
