I'm trying to use the ADC and internal reference to measure battery voltage on the nrf51422, while S210 is enabled.
From the example nrf51-ble-app-temp-master, I found...
I have Nokia Lumia 630 and it works well with nRF51822-EK but only with SDK nrf51822_v5.1.0.36092 and SoftDevice 6.0.0. Now I decided to try DFU OTA. I programmed bootloader...
Hello,
I found that there is a multiprotocol demo in folder Board\nrf6310\s110\experimental\ble_app_multiactivity_beacon,then I found it can implement concurrent connected...
Dear Sir
We got the problem on DFU upload firmware, it always failed in second DFU . We must unpair the device at iOS setting panel. Before next DFU.
Here is the log data...
Hi All,
My requirement is to read the data from nRF51822 device that is connected to a bluetooth and bluetooth is connected to a system using a .Net application.
I have...
Hi everyone,
I'm using the nRF51822 (pca10000 Dongle + pca10005).
My plan is to send one byte over the radio.
I tried to use the SDK-Example as a template but it's...
Hi Nordic, I come from this question: devzone.nordicsemi.com/.../
So, my doubt is: what events are triggered in a slave channel while it is not communicating to a master...
good time dear Engineers!
Please explain how to use correctly HANDLE RANGE in functions of discovering.
I use CENTRAL with up to 8 possible connections to PERIPH, so pls...
Folks,
Have a very puzzling problem (which means I must have done something really silly :-)
Built a prototype in which the nRF52 section is a clone of the one in the...
Hi,
My team has created a custom board with NRF 52 and were able to flash the blinky sample successfully. The LED connected to P.20 is glowing on the custom board after...
Hello! I need to start a sequence of 26 pulses after getting low level signal on gpiote pin.
I can do it in gpiote event handler but I need it most of the time so I want...
I've been developing an application using the NRF52 DK and everything has been going as planned. I then made my own PCB which would take these modules by Rigado. The BMD-300...
Hi,
I am creating an application based on ble_app_hrs_c (central role). I have a few questions on this.
o I do not understand whitelist_load(). It first gets a list...
Good morning Nordic team,
I was measuring the nRF52832 chip in DC/DC mode. Everything went just as expected.
Now I was looking at the current consumption when the radio...
Hi guys. I have a EVK_NINA_B1 board which is based on nrf52832 and SDK12. I am trying to run the ble_peripheral/ble_app_uart/ from examples. I can send message through "nrf...
Hello,
I use SDK 11 with nRF52, softdevice s132.
I am able to successfully use the bootloader in serial mode (with UART) to upgrade the application, but an error occurred...
hi nordic,
After i received this kit from Mouser Electronic, when i got it check the board which some question,
we examined its outward appearance and found that this...
Hi,
I have my nrf52 DK. I would like to advertise as Beacon and be BLE (which I can connect to via iOS app) device at the same time. Do you know any examples of this kind...
Why does the macro CHECK_RAM_START_ADDR only check for C_LINK_CNT and P_LINK_CNT and not the SEC_COUNT? It is always set to 0 in the macro.
I have increased the central_sec_count...
Hi ，
I use timer to handle pwm signal,
1.when calling button by phone is pressed,
Timer starts,(function:on_key_trig_speaker_event())
2.pwm signal run (speaker_meas_timeout_handler...
